RAVINE High Performance Universal Toilet Fill Valve Replacement Kit

1. නිෂ්පාදන අවසන්view

The RAVINE High Performance Universal Toilet Fill Valve Replacement Kit is designed to replace most standard toilet fill valves, offering quiet operation, fast tank refilling, and efficient water usage. This universal design ensures compatibility with a wide range of toilet models, making it an ideal solution for maintaining optimal toilet performance.

ප්රධාන ලක්ෂණ:

• වෙහෙස නොබලා ස්ථාපනය: ඉක්මන් සහ සරල සැකසුම සඳහා නිර්මාණය කර ඇත.
• නිහඬ මෙහෙයුම: Minimizes noise during the tank refill process.
• Fast Fill Efficiency: Ensures rapid tank refilling, reducing wait times between flushes.
• විශ්ව අනුකූලතාව: Fits most toilet makes and models.
• Water Conservation: Optimizes water delivery to reduce waste.

2 ආරක්ෂිත තොරතුරු

Please read all instructions carefully before beginning installation. Failure to follow these instructions may result in property damage or personal injury.

• Always turn off the water supply to the toilet before starting any work.
• ආරක්ෂිත කණ්නාඩි වැනි සුදුසු පුද්ගලික ආරක්ෂක උපකරණ පළඳින්න.
• වැඩ කරන ප්‍රදේශය හොඳින් ආලෝකමත් වී ඇති බවත් බාධා වලින් තොර බවත් සහතික කර ගන්න.
• ඔබට කිසියම් පියවරක් පිළිබඳව සැකයක් ඇත්නම්, සුදුසුකම් ලත් ජලනල කාර්මිකයෙකුගෙන් විමසන්න.
• Do not overtighten connections, as this may damage components.

3. පැකේජ අන්තර්ගතය

ස්ථාපනය ආරම්භ කිරීමට පෙර සියලුම සංරචක පවතින බව තහවුරු කර ගන්න:

• RAVINE Universal Toilet Fill Valve
• නැවත පිරවීමේ නළය
• ගෙඩි සවි කිරීම
• කෝන් වොෂර්

4. ස්ථාපන උපදෙස්

4.1. සකස් කිරීම

1. Turn off the water supply valve located at the wall behind the toilet.
2. Flush the toilet to empty the tank. Hold the flush lever down to drain as much water as possible.
3. Use a sponge or towel to remove any remaining water from the tank.
4. Disconnect the water supply line from the bottom of the old fill valve.
5. Unscrew the mounting nut from the underside of the tank and remove the old fill valve.

4.2. පියවරෙන් පියවර ස්ථාපනය

6. Insert the new RAVINE fill valve into the hole at the bottom of the toilet tank. Ensure the cone washer is properly seated on the valve shank inside the tank.
7. From the underside of the tank, thread the mounting nut onto the valve shank. Hand-tighten the nut firmly. Do not overtighten.
8. Connect the refill tube to the small port on the side of the fill valve and clip the other end to the overflow pipe. Ensure the tube is positioned above the water line.
9. Reconnect the water supply line to the bottom of the new fill valve. Hand-tighten, then use a wrench for a quarter turn to ensure a snug, leak-free connection.
10. Slowly turn on the water supply valve. The tank will begin to fill. Check for any leaks at the connections.

4.3. Adjusting Water Level

The RAVINE fill valve allows for easy adjustment of the water level in the toilet tank. This adjustment is typically done by rotating the float cup or a screw mechanism on the valve body.

1. Locate the water level adjustment mechanism on the fill valve. This is usually a screw or a sliding clip on the float assembly.
2. To raise the water level, turn the adjustment screw clockwise or slide the clip upwards. To lower the water level, turn the screw counter-clockwise or slide the clip downwards.
3. Flush the toilet after each adjustment to allow the tank to refill and observe the new water level. The water level should be approximately 1 inch below the top of the overflow pipe.

5. මෙහෙයුම

After flushing, the RAVINE fill valve automatically senses the drop in water level within the toilet tank. It then opens to allow fresh water to enter the tank and refill it to the preset level. The float mechanism rises with the water, and once the desired level is reached, the valve closes, stopping the water flow. The refill tube directs a small amount of water into the toilet bowl during the refill cycle to ensure proper bowl water level.

6. නඩත්තු කිරීම

Regular maintenance helps ensure the longevity and optimal performance of your RAVINE fill valve.

• වරින් වර පරීක්ෂා කිරීම: Annually inspect the fill valve for any signs of wear, cracks, or mineral buildup.
• Cleaning the Filter Screen: If water flow becomes slow, the inlet filter screen at the base of the valve may be clogged. Turn off the water supply, disconnect the supply line, and carefully remove the filter screen for cleaning. Rinse it under running water to remove debris, then reassemble.
• ඛනිජ ගොඩනැගීම: For areas with hard water, mineral deposits can affect valve operation. If necessary, disassemble the top portion of the valve (refer to specific instructions if provided with the product for detailed disassembly) and soak components in a vinegar solution to dissolve mineral buildup. Rinse thoroughly before reassembly.

7. දෝශ නිරාකරණය

පොදු ගැටළු සහ ඒවාට විසඳුම් සඳහා පහත වගුව බලන්න.

8. පිරිවිතර

9. වගකීම් සහ සහාය

For warranty information or technical support, please refer to the product packaging or contact RAVINE customer service. Keep your purchase receipt as proof of purchase for any warranty claims.