හැඳින්වීම
The TP-LINK TX-6610 is a 1-Port Gigabit GPON Terminal designed to provide high-speed fiber optic network access. It complies with ITU G.984.x GPON standards, offering robust compatibility and performance for your internet connection. This manual provides detailed instructions for setting up, operating, and maintaining your TX-6610 device.
ඉහළ view of the TP-LINK TX-6610 GPON Terminal.
පැකේජයේ අන්තර්ගතය
ඔබ ආරම්භ කිරීමට පෙර, කරුණාකර ඔබේ පැකේජයේ පහත අයිතම අඩංගු දැයි තහවුරු කරගන්න:
- TP-LINK TX-6610 GPON Terminal
- RJ45 ඊතර්නෙට් කේබලය
- Network Adapter (Power Supply)
- ඉක්මන් ස්ථාපන මාර්ගෝපදේශය
සැලසුම
Follow these steps to set up your TX-6610 GPON Terminal:
- ස්ථානගත කිරීම: Place the TX-6610 in a stable, well-ventilated location, away from direct sunlight and heat sources. Ensure it is within reach of your fiber optic connection and power outlet.
- ෆයිබර් ඔප්ටික් කේබලය සම්බන්ධ කරන්න: Carefully connect the fiber optic cable from your service provider to the SC/APC Port on the TX-6610. Ensure the connector is clean and properly seated.
- ඊතර්නෙට් කේබලය සම්බන්ධ කරන්න: Connect one end of the provided RJ45 Ethernet cable to the Gigabit RJ45 Port on the TX-6610 and the other end to your computer or router.
- බල ඇඩැප්ටරය සම්බන්ධ කරන්න: Plug the network adapter into the power input port on the TX-6610, then plug the other end into a standard electrical outlet.
- බල ගැන්වීම: උපාංගය සක්රිය කිරීමට Power On/Off බොත්තම ඔබන්න.
කෝණික view of the TX-6610, highlighting the indicator lights and side port.
ක්රියාත්මක වෙනවා
Once the TX-6610 is powered on, observe the indicator lights for its operational status:
- බලය: Solid green indicates the device is powered on.
- ජීපීඑන්: Solid green indicates a successful connection to the GPON network. Blinking indicates data transmission.
- LOS (Loss of Signal): If this light is red or off when it should be on, it indicates a problem with the fiber optic connection.
- LAN: Solid green indicates a successful Ethernet connection to a device. Blinking indicates data transmission.
The TX-6610 acts as a bridge between your local network and the GPON fiber network. Configuration is typically handled by your Internet Service Provider (ISP) via OMCI remote management. For advanced settings, you may access the device's web management interface using a web browser, if enabled by your ISP.
නඩත්තු කිරීම
To ensure the longevity and optimal performance of your TX-6610:
- උපාංගය පිරිසිදුව හා දූවිලි වලින් තොරව තබා ගන්න.
- අධික උනුසුම් වීම වැළැක්වීම සඳහා නිසි වාතාශ්රය සහතික කරන්න.
- උපාංගය අධික උෂ්ණත්වයට හෝ ආර්ද්රතාවයට නිරාවරණය කිරීමෙන් වළකින්න.
- Do not attempt to open the device casing, මෙය වගකීම් සහතිකය අවලංගු කර ඔබව විදුලි අනතුරු වලට නිරාවරණය කළ හැකි බැවිනි.
- If the device is unresponsive, you can use the RESET බොත්තම. Press and hold the RESET button for approximately 5-10 seconds to restore the device to its factory default settings. This will erase any custom configurations.
දෝෂගවේෂණය
If you encounter issues with your TX-6610, refer to the following common problems and solutions:
- විදුලි පහනක් නැත: Ensure the power adapter is securely connected to both the device and the electrical outlet. Try a different outlet.
- LOS Light is Red/Off: This indicates a loss of optical signal. Check the fiber optic cable connection to the SC/APC port. Ensure the cable is not damaged or bent sharply. Contact your ISP if the issue persists, as it may be a problem with their network or the fiber line.
- GPON Light Not Solid Green: The device is not successfully registered with the GPON network. Verify the fiber connection. Your ISP may need to provision the device.
- LAN Light Not On: Check the Ethernet cable connection between the TX-6610 and your connected device (computer/router). Try a different Ethernet cable or port on your connected device.
- අන්තර්ජාල ප්රවේශය නැත: Even if all lights appear normal, there might be an issue with your ISP's service or your router's configuration. Restart the TX-6610 and your router. If the problem continues, contact your ISP.
- Device Unresponsive/Frozen: Use the RESET button to restore factory defaults (see Maintenance section).
පිරිවිතර
දෘඪාංග විශේෂාංග
| විශේෂාංගය | විස්තරය |
|---|---|
| අතුරු මුහුණත | 1x 10/100/1000Mbps RJ45 Port, 1x SC/APC Port |
| බොත්තම් | 1x Power On/Off Button, 1x RESET Button |
| බාහිර බල සැපයුම | 9VDC/0.6A |
| IEEE ප්රමිති | IEEE 802.3, 802.3u, 802.1Q, 802.1p |
| Data Rate (Upstream) | 1.244Gbps |
| Data Rate (Downstream) | 2.488Gbps |
| මානයන් (W x D x H) | 4.0 x 1.5 x 4.2 අඟල් (102.7 x 37.9 x 106.9 මි.මී.) |
| උපරිම දුර | 0 ~ 20 Km |
| GPON Standards | ITU-T G.984.1, G.984.2, G.984.3, G.984.4 |
| ඔප්ටිකල් මොඩියුලය | Class C+, Receiver APD-TIA, DFB Laser Transmitter |
| Wavelength (Upstream) | 1310nm |
| Wavelength (Downstream) | 1490nm |
මෘදුකාංග විශේෂාංග
| විශේෂාංගය | විස්තරය |
|---|---|
| QoS | VLAN-based Flow-Rating, Service Scheduling Rules (SP/WRR), Upstream Priority Label (802.1D), Rate Limit, Traffic Formation, Congestion Control (Tail-Drop) |
| VLAN | 802.1Q VLAN tag, Transparent/Translation/Trunk VLAN modes, Authentication by SN and Password, Auto Detection VLAN |
| ආරක්ෂාව | AES Encryption, Packet Filter by VLAN |
| කළමනාකරණය | Web, OMCI, Telnet, Fixed-Management IP, Factory Default Reset (button/Web UI), Real-time Statistics, Optical Diagnostics |
| උසස් විශේෂාංග | Upstream/Downstream FEC, Dynamic Bandwidth Allocation (DBA) compatible with NSR/SR (up to 16 T-CONTs and 256 GEM Ports), Optical power detection, Dying Gasp, Terminal Silent mechanism, Energy saving 802.3az EEE |
| අයිජීඑම්පී | IGMP v2/IGMP v3 Snooping/Proxy |
| සහතික | CE, FCC, RoHS |
| පද්ධති අවශ්යතා | Microsoft Windows 98SE, NT, 2000, XP, Vista, 7, 8; MAC OS; NetWare; UNIX; Linux |
පාරිසරික තත්ත්වයන්
| තත්ත්වය | පරාසය |
|---|---|
| මෙහෙයුම් උෂ්ණත්වය | 0°C ~ 40°C (32°F ~ 104°F) |
| ගබඩා උෂ්ණත්වය | -40°C ~ 70°C (-40°F ~ 158°F) |
| මෙහෙයුම් ආර්ද්රතාවය | 10% ~ 90% ඝනීභවනය නොවන |
| ගබඩා ආර්ද්රතාවය | 5% ~ 90% ඝනීභවනය නොවන |
පරිශීලක ඉඟි
Based on general user experiences with similar GPON terminals:
- Always ensure the fiber optic cable is not bent or kinked, as this can severely degrade signal quality.
- If you experience intermittent connectivity, try restarting both the GPON terminal and any connected router or computer.
- For optimal performance, connect your primary router directly to the Gigabit Ethernet port of the TX-6610.
වගකීම් සහ සහාය
This TP-LINK product is covered by the manufacturer's warranty. Please refer to the warranty card included in your package or visit the official TP-LINK website for detailed warranty terms and conditions. For technical support, troubleshooting assistance, or service inquiries, please contact TP-LINK customer support or your Internet Service Provider (ISP).
