SC07 Universal 2-Channel Garage Gate Receiver Module

1. හැඳින්වීම

The SC07 Universal 2-Channel Garage Gate Receiver Module is designed to provide versatile control for various automation systems. This module is compatible with a wide range of remote controls operating on frequencies between 300MHz and 900MHz, supporting both fixed and rolling code technologies. It is ideal for integration into gate automation systems, burglar alarm systems, electric doors, windows, and lifting equipment. Its compact design, low power consumption, and ease of connection make it a reliable solution for enhancing your existing control systems.

2. පිරිවිතර

3. පැකේජ අන්තර්ගතය

• 1 x SC07 Receiver Module
• 1 x කුඩා ඇන්ටෙනාව
• 1 x ඉංග්‍රීසි අත්පොත

4. පිහිටුවීම

4.1 බල ආදාන තේරීම (PIS)

The receiver operates on AC/DC 9V-30V. It is crucial to correctly set the Power Input Selector (PIS) based on your power supply voltage:

• ආදාන පරිමාව නම්tage 24V ට වඩා වැඩි නම්, 2 සහ 3 පින් කෙටි කරන්න.
• ආදාන පරිමාව නම්tage 24V ට වඩා අඩුය, 1 සහ 2 පින් කෙටි කරන්න.

4.2 රැහැන් සටහන

Connect the receiver module to your gate automation system or other devices using the terminal block. Refer to the diagram below for connection points:

රූපය: ඉදිරිපස view of the white receiver module, showing PWR (Power Input), OUT1 (Output 1), OUT2 (Output 2), GND (Ground), and ANT (Antenna) terminals. Also visible are L1/L2 LEDs, S1/S2 learn buttons, and the 8-position DIP switch.

• PWR: Connect your AC/DC 9V-30V power supply here.
• OUT1 / CH1: Output for Channel 1 (relay output).
• OUT2 / CH2: Output for Channel 2 (relay output).
• ජීඑන්ඩී: බිම් සම්බන්ධතාවය.
• කූඹියා: Connect the provided small antenna here for optimal signal reception.

5. මෙහෙයුම් උපදෙස්

5.1 Brand Selection (DIP Switches)

The receiver features 8 DIP switches to select the correct brand and frequency for the remote control you wish to program. Each remote brand may require a specific DIP switch combination. Refer to the diagram below for common brand settings:

රූපය: විස්තරාත්මක view of the 8-position DIP switch with various settings for different remote control brands and frequencies (e.g., Marantec, Hormann, Nice, etc.). Switches are labeled 1 through 8.

To select a brand, move the corresponding DIP switches UP or DOWN as indicated for your remote control's brand and frequency. For example, for a 433.92MHz Marantec remote control, move Dip-switch 7 UP.

5.2 Programming a New Remote Control

1. Select Brand: Ensure the correct brand and frequency are selected using the 8 DIP switches (refer to Section 5.1).
2. ඉගෙනුම් මාදිලිය ඇතුළු කරන්න: Press the learn button (S1 for Channel 1, S2 for Channel 2) on the receiver module. The corresponding LED (L1 or L2) will turn on, indicating it's in learning mode.
3. Transmit Remote Signal: Press the desired button on your remote control. The LED on the receiver will flash 4 times, confirming successful programming.
4. අතිරේක බොත්තම් සඳහා නැවත කරන්න: If your remote has multiple buttons you wish to program, repeat step 2 and 3 for each button.
5. දෙවන නාලිකාව: The programming procedure for the second channel (using S2 and L2) is identical.

5.3 එර්asing All Data from Memory

To clear all programmed remote controls from the receiver's memory:

• Press and hold either learn button (S1 or S2). The LED will begin to flash.
• Continue holding the button until the LED turns off. All saved data in the memory will be permanently erased and cannot be recovered.

6 පරිශීලක ඉඟි

• බල සැපයුම: Always double-check your power supply voltage (AC/DC 9V-30V) and ensure the PIS (Power Input Selector) is correctly configured before powering on the module.
• ඇන්ටෙනා ස්ථානගත කිරීම: For optimal reception range, ensure the small antenna is connected and positioned away from metal obstructions.
• පරීක්ෂා කිරීම: After programming a remote, always test the range and functionality of the receiver before fully integrating it into your system.
• බාධා කිරීම්: The receiver is designed not to interfere with other remotes and receivers, but ensure your remote is transmitting on the correct frequency for the selected brand.

7. දෝශ නිරාකරණය

• Remote Not Programming:
  • Verify that the DIP switches are set correctly for your remote control's brand and frequency.
  • Ensure your remote control has a working battery and is transmitting a signal.
  • Try erasing all data from the receiver's memory (Section 5.3) and then re-program the remote.
• කෙටි මෙහෙයුම් පරාසය:
  • Check that the antenna is securely connected and not obstructed by metal objects.
  • Ensure there are no major sources of radio frequency interference nearby.
  • The stated range of 30-50 meters is for open areas; obstructions will reduce this.
• No Power to Receiver:
  • Check all wiring connections to the PWR and GND terminals.
  • Verify that your power supply is providing the correct voltage (9V-30V AC/DC).
  • Ensure the PIS (Power Input Selector) is correctly set for your voltage.
• Receiver Not Responding to Programmed Remote:
  • Confirm that the remote was successfully programmed (LED flashes 4 times).
  • Check if the remote's frequency matches the DIP switch settings.
  • Ensure the remote is not too far from the receiver.

8. නඩත්තු කිරීම

• පිරිසිදු කිරීම: මොඩියුලය පිරිසිදුව හා දූවිලි හා සුන්බුන් වලින් තොරව තබා ගන්න. පිරිසිදු කිරීම සඳහා මෘදු වියළි රෙද්දක් භාවිතා කරන්න.
• පරිසරය: Avoid exposing the module to extreme temperatures, high humidity, or direct water contact.
• රැහැන් පරීක්ෂාව: Periodically check all wiring connections for looseness or damage.

9. වගකීම් සහ සහාය

For warranty information, technical support, or any questions not covered in this manual, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.