AKO D14918 Programming Key Instruction Manual

D149H181 Ed.08

AKO-D14918

ද AKO-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality

අනතුරු ඇඟවීම්

-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.

විස්තරය

1. LED COM
2. වාර්තා යතුර
3. EXTERNAL POWER CONNECTOR
4. READ KEY
5. LED ඔන්
6. CONNECTOR CABLE

ගැළපුම

Refer to the instruction manual of your equipment on its compatibility with the AKO-D14918 programming key.

Connecting incompatible devices can permanently damage the key.

රැහැන් ඇදීම

1. වැදගත්: Pay attention to the orientation of the connector.
2. AKO-80018 
   (විකල්ප)
3. AKO-D14918

බල සැපයුම

-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (AKO-80018 or equivalent).

මෙහෙයුම

වැදගත්: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.

RECORD key

Write the data contained in the key memory to the controller.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

READ key

It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

LED ඔන්

Steady or flashing: Indicates that the key is connected to the controller.

LED COM

ස්ථාවර: Indicates an error in the transmission/reception of data
වේගයෙන් දැල්වීම: Indicates transmission/reception of data in progress. At the end of the transmission LED COM නිවා දමයි.
මන්දගාමී දැල්වීම: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.

සටහන: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.

වැදගත්: කවදාවත් නැහැ disconnect the programming key during data transmission.

තාක්ෂණික පිරිවිතර

Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
සැපයුම් වෙළුමtage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
පාරිසරික පිරිවිතර:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC

අකෝ ඉලෙක්ට්‍රොමෙනිකා, SA
Av. රොකට්, 30-38 | 08812 Sant Pere de Ribes | බාර්සිලෝනා | එස්පානා

35D149181 REV.07 2025

අපගේ තාක්ෂණික පත්‍රවල විස්තර කර ඇති ඒවාට තරමක් වෙනස් විය හැකි ද්‍රව්‍ය සැපයීමේ අයිතිය අප සතුය.
යාවත්කාලීන තොරතුරු අපගේ වෙබ් අඩවියේ ඇත webඅඩවිය.