නිෂ්පාදනය අවසන්view
The DIG PRV075 is a pipe thread adjustable pressure regulator designed to reduce and regulate incoming water pressure for drip irrigation and micro-sprinkler systems. It ensures the system operates within the appropriate pressure range, typically between 28 PSI and 60 PSI, providing consistent outlet pressure regardless of upstream fluctuations.
රූපය: ඉදිරිපස view of the DIG PRV075 Adjustable Drip Pressure Regulator, showing its black plastic body and red adjustment cap.
ප්රධාන ලක්ෂණ:
- Adjustable pressure range with a single screw for fine-tuning.
- Rolling diaphragm design prevents debris from entering the spring assembly, ensuring longevity.
- Maintains reliable control of outlet pressure despite variations in incoming pressure or flow.
- Equipped with 3/4" female pipe thread (FPT) inlet and outlet for compatibility with standard connections.
සැකසුම සහ ස්ථාපනය
Proper installation is crucial for the optimal performance of your DIG PRV075 pressure regulator. Follow these steps carefully:
- සම්බන්ධතා ලක්ෂ්ය හඳුනා ගන්න: The PRV075 has 3/4" female pipe threads on both the inlet and outlet. Ensure your irrigation system components have compatible male pipe threads.
- Prepare the Connection: Turn off the main water supply to the irrigation line where the regulator will be installed.
- Thread the Regulator:
- Apply thread sealant tape (Teflon tape) or pipe dope to the male threads of your water source connection.
- Carefully thread the inlet side of the PRV075 onto the prepared male thread. Hand-tighten first, then use a wrench for an additional 1 to 2 turns until snug. Do not overtighten.
- Repeat the process for the outlet side, connecting it to your drip irrigation or micro-sprinkler system.
- කාන්දුවීම් සඳහා පරීක්ෂා කරන්න: Slowly turn on the main water supply and inspect all connections for leaks. Tighten any leaking connections gently.
රූපය: පැත්ත view of the DIG PRV075 Pressure Regulator held in a hand, illustrating its compact size and showing approximate dimensions of 5.1 inches (12 cm) in length.
මෙහෙයුම් උපදෙස්
The DIG PRV075 is designed for easy pressure adjustment. Follow these steps to set the desired operating pressure:
- ගැලපුම් ඉස්කුරුප්පු ඇණ සොයා ගන්න: The pressure adjustment screw is located under the red cap at one end of the regulator. Gently pry off the red cap to expose the screw.
- පීඩනය සකසන්න:
- Use a flathead screwdriver to turn the adjustment screw.
- Turning the screw දක්ෂිණාවර්තව කැමැත්ත වැඩි කරන්න the outlet pressure.
- Turning the screw වාමාවර්තව කැමැත්ත අඩු වීම the outlet pressure.
- Make small adjustments and observe the system's performance. For precise adjustment, use a pressure gauge downstream of the regulator.
- මෙහෙයුම් පරාසය: The regulator is designed to operate within a range of 28 PSI to 60 PSI. Do not attempt to adjust outside this range.
- Replace Cap: Once the desired pressure is set, securely replace the red protective cap.
නඩත්තු කිරීම
The DIG PRV075 is designed for minimal maintenance. However, periodic checks can ensure its long-term performance:
- කාන්දුවීම් සඳහා පරීක්ෂා කරන්න: Periodically check all connections for any signs of water leaks. Address any leaks promptly by tightening connections or replacing thread sealant.
- සුන්බුන් සඳහා පරීක්ෂා කරන්න: While the rolling diaphragm helps prevent debris, if you notice inconsistent pressure or reduced flow, it may indicate debris accumulation. Turn off the water, disconnect the regulator, and inspect the inlet and outlet for any blockages. Clean gently with water if necessary.
- ශීත ඍතුකරණය: In regions subject to freezing temperatures, it is recommended to drain the irrigation system, including the pressure regulator, to prevent damage from freezing water.
දෝෂගවේෂණය
| ගැටලුව | විය හැකි හේතුව | විසඳුම |
|---|---|---|
| No water flow or very low flow |
|
|
| Pressure too high or too low (and cannot be adjusted) |
|
|
| සම්බන්ධතා වලින් ජලය කාන්දු වීම |
|
|
පිරිවිතර
- ආකෘතිය: PRV075
- වෙළඳ නාමය: නියෝජ්ය පොලිස්පති
- ද්රව්ය: Plastic body, Stainless Steel exterior finish (referring to internal spring/components)
- ආදාන/අවුට්ලට් සම්බන්ධතාවය: 3/4" Female Pipe Thread (FPT)
- සකස් කළ හැකි පීඩන පරාසය: 28 PSI සිට 60 PSI දක්වා
- මානයන් (L x W x H): ආසන්න වශයෙන් 4 x 2 x 3 අඟල්
- අයිතමයේ බර: ආසන්න වශයෙන් 1.6 අවුන්ස
- වරායන් ගණන: 2
- කපාට වර්ගය: Globe Valve (as per specification, though it's a regulator)
- UPC: 013158333333
වගකීම් සහ සහාය
For information regarding product warranty, technical support, or replacement parts, please contact DIG customer service directly. Refer to the official DIG webවඩාත්ම වත්මන් සම්බන්ධතා තොරතුරු සහ වගකීම් කොන්දේසි සඳහා වෙබ් අඩවිය හෝ නිෂ්පාදන ඇසුරුම්කරණය.
You can visit the official DIG store for more information: DIG Official Store
