Genie 36163R.S IntelliCode ගරාජ් දොර විවෘත කරන්නා ග්‍රාහක උපදෙස් අත්පොත

1. හැඳින්වීම

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Genie 36163R.S IntelliCode Garage Door Opener Receiver. This receiver is designed to enhance the compatibility of your garage door opener system with Genie IntelliCode remotes, operating on both 315MHz and 390MHz frequencies.

Please read all instructions carefully before beginning installation or operation to ensure proper function and safety.

2. පැකේජ අන්තර්ගතය

The Genie 36163R.S IntelliCode Receiver package includes:

• One (1) Genie 36163R.S IntelliCode Receiver unit.

සටහන: This package contains the receiver unit only. Transmitters (remotes), wiring, and power packs are not included and must be acquired separately if needed. This receiver is commonly used as a component in the GIRUD-1T Receiver Kit.

3 ආරක්ෂිත තොරතුරු

සෑම විටම පහත සඳහන් ආරක්ෂක පියවරයන් නිරීක්ෂණය කරන්න:

• Disconnect power to the garage door opener before installing or servicing the receiver.
• සියලුම රැහැන් සම්බන්ධතා ආරක්ෂිත බවත් දේශීය විදුලි කේතවලට අනුකූල බවත් සහතික කර ගන්න.
• Keep hands and clothing clear of the garage door and its moving parts during operation.
• Do not allow children to operate the garage door opener or play with remote controls.
• Test the safety reversal system of your garage door opener after installation.

4. පිහිටුවීම සහ ස්ථාපනය

The Genie 36163R.S receiver is designed for straightforward installation. Follow these steps:

4.1. Identify Components

රූපය 1: ඉහළ view of the Genie 36163R.S IntelliCode Receiver. This image shows the overall compact design of the receiver unit.

රූපය 2: පහළ view of the Genie 36163R.S IntelliCode Receiver. The label displays the receiver model (315390R2) and FCC compliance information.

රූපය 3: පැත්ත view of the Genie 36163R.S IntelliCode Receiver. This image highlights the POWER, COMMON, and WALLBUTTON TERMINAL connections, along with the LEARN CODE INDICATOR LED and LEARN CODE BUTTON.

4.2. ග්‍රාහකය රැහැන්ගත කිරීම

1. බලය විසන්ධි කරන්න: Before making any connections, ensure the power to your garage door opener is disconnected at the circuit breaker.
2. Locate Terminals: On your garage door opener power head, locate the terminals for the wall control button. These are typically labeled "COMMON" and "WALL BUTTON" or similar.
3. Connect Receiver Wires:
   • Connect a wire from the receiver's "COMMON" terminal to the "COMMON" terminal on your garage door opener.
   • Connect a wire from the receiver's "WALLBUTTON TERMINAL" to the "WALL BUTTON" terminal on your garage door opener.
   • Connect the receiver's "POWER" terminal to a 24-volt power source. This may be available from your garage door opener's accessory terminals or require a separate 24V power pack (not included).
4. ආරක්ෂිත සම්බන්ධතා: සියලුම වයර් සම්බන්ධතා තදින් සහ ආරක්ෂිතව ඇති බවට වග බලා ගන්න.

4.3. ග්‍රාහකය සවි කිරීම

Mount the receiver in a location that is protected from moisture and physical damage, preferably near the garage door opener. Ensure the antenna wire hangs freely and is not coiled or obstructed for optimal signal reception.

5. Operating Instructions: Programming Remotes

This receiver is compatible with Genie IntelliCode remotes. To program a remote to the receiver:

1. බලය ප්‍රතිස්ථාපනය කරන්න: Reconnect power to your garage door opener. The LEARN CODE INDICATOR LED on the receiver should illuminate or flash.
2. ඉගෙන ගන්න බොත්තම ඔබන්න: Press and release the "LEARN CODE BUTTON" on the receiver (refer to Figure 3). The LEARN CODE INDICATOR LED will begin to flash slowly.
3. දුරස්ථ පාලකය සක්‍රිය කරන්න: Within 30 seconds, press and release the button on your IntelliCode remote control that you wish to program.
4. තහවුරු කිරීම: The LEARN CODE INDICATOR LED on the receiver will stop flashing and remain lit for a moment, then turn off, indicating successful programming.
5. පරීක්ෂණ දුරස්ථ පාලකය: Press the programmed button on your remote control to test the garage door opener's operation.
6. Program Additional Remotes: Repeat steps 2-5 for any additional IntelliCode remotes you wish to program.

සටහන: If the remote does not operate the garage door, ensure the remote has fresh batteries and repeat the programming steps.

6. දෝශ නිරාකරණය

• Receiver not responding:
  • Check power connections to the receiver. Ensure 24V power is supplied.
  • Verify wiring to the garage door opener's wall button terminals is correct and secure.
  • Ensure the garage door opener itself has power.
• Remote not operating door after programming:
  • Confirm the remote is a Genie IntelliCode remote.
  • Check the remote's battery. Replace if necessary.
  • Repeat the programming steps carefully.
  • දුරස්ථ පාලකය ග්‍රාහකයාගේ පරාසය තුළ ඇති බව සහතික කර ගන්න.
• අඩු කළ දුරස්ථ පරාසය:
  • Ensure the receiver's antenna wire is fully extended and not obstructed or coiled.
  • Check for sources of radio interference (e.g., other electronic devices, metal objects).
  • Consider relocating the receiver for better line-of-sight to where remotes are typically used.

7. පිරිවිතර

8. නඩත්තු කිරීම

The Genie 36163R.S IntelliCode Receiver requires minimal maintenance. Periodically:

• ගෙවී යාමේ හෝ හානිවීමේ සලකුණු සඳහා රැහැන් පරීක්ෂා කරන්න.
• Ensure the receiver is free from dust and debris.
• Verify the antenna is unobstructed.

No user-serviceable parts are inside the receiver unit. Do not attempt to open or repair the unit yourself.

9. වගකීම් සහ සහාය

For warranty information or technical support, please refer to the official Genie website or contact Genie customer service. Keep your purchase receipt for warranty claims.

Genie Customer Service: Refer to product packaging or the official Genie webවත්මන් සම්බන්ධතා තොරතුරු සඳහා අඩවිය.