1. හැඳින්වීම
The LASERLINER MultiFinder Plus is a highly versatile and reliable locating device designed for detecting various materials within walls, ceilings, and floors. Equipped with multiple integrated sensors, it provides precise detection of wood, metal (including copper, steel, and iron), and live electrical wires. Its user-friendly LCD screen and automatic calibration feature ensure easy and safe operation for both professionals and DIY enthusiasts.
This manual provides comprehensive instructions for the safe and effective use, maintenance, and troubleshooting of your MultiFinder Plus. Please read it thoroughly before operating the device.
2 ආරක්ෂිත තොරතුරු
WARNING: Always exercise extreme caution when detecting near electrical installations. The device indicates live wires, but it is crucial to verify findings with other methods if there is any doubt. Disconnect power before drilling or cutting into walls.
- භාවිතයට පෙර සියලුම උපදෙස් කියවන්න.
- උපාංගය අධික උෂ්ණත්වයට, ආර්ද්රතාවයට හෝ සෘජු හිරු එළියට නිරාවරණය නොකරන්න.
- Use only the specified battery type (9V alkaline battery, Type 6LR 61).
- උපාංගය පිරිසිදුව හා වියලි ලෙස තබා ගන්න.
- උපාංගය විවෘත කිරීමට හෝ වෙනස් කිරීමට උත්සාහ නොකරන්න. අලුත්වැඩියාවන් සිදු කළ යුත්තේ බලයලත් පුද්ගලයින් විසින් පමණි.
- Be aware of potential hazards such as gas pipes, water pipes, and electrical cables.
Image: The display shows a permanent electrical warning symbol (lightning bolt in triangle) when live wires are detected, indicating a potential hazard.
Image: A red warning light illuminates on the top of the device, accompanied by a lightning bolt symbol on the display, to alert the user to the presence of live electrical current.
3. පැකේජ අන්තර්ගතය
- LASERLINER MultiFinder Plus device
- 1 x 9V alkaline battery (Type 6LR 61)
- පරිශීලක අත්පොත (මෙම ලේඛනය)
4. නිෂ්පාදන අවසන්view
Familiarize yourself with the components of your MultiFinder Plus:
රූපය: ඉදිරිපස view of the MultiFinder Plus, showing the LCD display, Mode button, and CAL button.
- LCD සංදර්ශකය: Shows detection mode, signal strength, battery status, and warning indicators.
- මාදිලි බොත්තම: Used to switch between detection modes (Wood/Stud, Metal, AC).
- CAL බොත්තම: Used for automatic calibration.
- Detection Sensor Area: Located on the back of the device, this area must be placed flat against the surface for accurate readings.
- බැටරි මැදිරිය: Located on the back for battery installation.
- අනතුරු ඇඟවීමේ ආලෝකය: A red LED on the top of the device illuminates when live electrical wires are detected.
රූපය: සමීප රූපය view of the orange 'Mode' button and the black 'CAL' (Calibration) button, indicating simple, one-touch operation.
Image: The LCD display provides clear information, including 'MOVE' arrows to guide the user during scanning, indicating the direction to move for optimal detection.
Image: The MultiFinder Plus features a backlight on its display, ensuring readability in low-light conditions.
5. පිහිටුවීම
5.1. බැටරි ස්ථාපනය
The MultiFinder Plus requires one 9V alkaline battery (Type 6LR 61).
- උපාංගයේ පිටුපස බැටරි මැදිරි කවරය සොයා ගන්න.
- කවරය විවෘත කරන්න.
- Insert the 9V battery, ensuring correct polarity (+ and -).
- බැටරි මැදිරි කවරය ආරක්ෂිතව වසා දමන්න.
Image: The open battery compartment of the MultiFinder Plus, showing the correct placement of a 9V battery. The battery cover is shown detached.
Image: The MultiFinder Plus device displayed alongside a 9V battery, illustrating the required power source.
5.2 මූලික ක්රමාංකනය
Before each use, or when switching detection modes, it is recommended to perform an automatic calibration.
- Place the device flat against the surface you intend to scan, ensuring no objects are directly beneath it.
- ඔබා අල්ලාගෙන සිටින්න CAL button until the calibration process is complete (indicated on the LCD).
- The device is now ready for use in the selected mode.
6. මෙහෙයුම් උපදෙස්
6.1. බලගැන්වීම සක්රිය/අක්රිය කිරීම සහ මාදිලි තේරීම
උපාංගය ක්රියාත්මක කිරීමට, ඔබන්න මාදිලිය button. To switch between detection modes (Wood/Stud, Metal, AC), press the මාදිලිය button repeatedly until the desired mode is displayed on the LCD.
6.2. Detection Modes and Depths
The MultiFinder Plus offers three primary detection modes:
- Stud-Scan (Wood): Detects wooden studs and beams.
- Detection Depth: Approximately 2 cm to 4 cm.
- Metal-Scan: Detects ferrous and non-ferrous metals, including copper, steel, and iron. This mode can also detect non-live cables under plaster.
- Detection Depth: Up to 10 cm.
- AC-Scan: Detects live electrical wires (110V-230V).
- Detection Depth: Approximately 4 cm to 5 cm.
Image: A visual diagram illustrating the approximate detection depths for different scan modes: Stud-Scan (2-4 cm), AC-Scan (4-5 cm for 110-230 Volt wires), and Metal-Scan (up to 10 cm).
6.3. ස්කෑන් කිරීමේ ක්රියා පටිපාටිය
- Select the appropriate detection mode using the මාදිලිය බොත්තම.
- Perform automatic calibration by pressing the CAL button while the device is flat against the surface.
- Slowly move the device horizontally across the surface. Maintain constant contact and pressure.
- Observe the LCD display for signal strength indicators and the 'MOVE' arrows, which guide you towards the center of the detected object.
- When an object is detected, the device will emit an acoustic signal, and the optical display will show a strong signal. For live wires, the red warning light will also illuminate.
- Mark the location of the detected object. For precise localization, scan the area from multiple directions.
6.4. Acoustic and Optical Signals
The MultiFinder Plus provides clear feedback:
- ධ්වනි සංඥාව: A beeping sound indicates the presence of a detected object. The frequency or intensity may change as you get closer to the object.
- දෘශ්ය සංදර්ශකය: The LCD screen shows a bar graph indicating signal strength. The higher the bars, the closer you are to the object.
- රතු අනතුරු ඇඟවීමේ ආලෝකය: Illuminates when live electrical wires are detected, providing an immediate visual alert.
7. නඩත්තුව සහ රැකවරණය
- පිරිසිදු කිරීම: උපාංගය මෘදු, ඩී සමඟ පිස දමන්නamp රෙදි. උල්ෙල්ඛ පිරිසිදු කරන්නන් හෝ ද්රාවණ භාවිතා නොකරන්න.
- ගබඩා: Store the device in a dry, dust-free environment, away from direct sunlight and extreme temperatures (-20 °C to 70 °C).
- බැටරි: කාන්දු වීම වැළැක්වීම සඳහා උපාංගය දිගු කාලයක් භාවිතා නොකරන්නේ නම් බැටරිය ඉවත් කරන්න.
- ක්රමාංකනය: Regular calibration ensures optimal performance.
8. දෝශ නිරාකරණය
| ගැටලුව | විය හැකි හේතුව | විසඳුම |
|---|---|---|
| සාවද්ය කියවීම් / වැරදි ධනාත්මක ප්රතිඵල | Improper calibration; high humidity; presence of other electronic devices nearby; user error (e.g., not holding flat). | Re-calibrate the device on a clear section of the wall. Ensure the device is held flat against the surface. Move away from other electronics. |
| උපාංගය බලගන්වන්නේ නැත | මිය ගිය හෝ වැරදි ලෙස ස්ථාපනය කර ඇති බැටරිය. | Check battery polarity. Replace with a new 9V alkaline battery. |
| Weak or no signal detection | Object too deep; incorrect mode selected; battery low. | Ensure the correct mode is selected for the target material. Check battery level. Note maximum detection depths for each mode. |
| නිරන්තර බීප් හඬ | Device is picking up ambient interference or needs re-calibration. | Move to a different area and re-calibrate. Ensure no hands or other objects are near the sensor area during calibration. |
9. පිරිවිතර
| විශේෂාංගය | විස්තර |
|---|---|
| ආදර්ශ අංකය | 080.965A |
| නිෂ්පාදකයා | ලේසර්ලයිනර් |
| හඳුනා ගැනීමේ මාදිලි | Wood/Stud, Metal (ferrous & non-ferrous, non-live wires), AC (live wires) |
| Max. Detection Depth (Wood/Stud) | Approx. 2 cm - 4 cm |
| Max. Detection Depth (Metal) | 10 දක්වා සෙ.මී |
| Max. Detection Depth (AC) | Approx. 4 cm - 5 cm (110V-230V) |
| බල සැපයුම | 1 x 9V Alkaline Battery (Type 6LR 61) |
| මෙහෙයුම් උෂ්ණත්වය | 0 °C සිට 40 °C (32 °F සිට 104 °F) |
| ගබඩා උෂ්ණත්වය | -20 °C සිට 70 °C (-4 °F සිට 158 °F) |
| මානයන් (W x H x D) | 80 x 186 x 40 mm (ආසන්න වශයෙන්. 3.15 x 7.32 x 1.57 අඟල්) |
| බර | ග්රෑම් 420 (ආසන්න වශයෙන් රාත්තල් 0.93) |
10. වගකීම් සහ සහාය
Laserliner products are manufactured with high quality standards and undergo strict quality control. This product comes with a standard manufacturer's warranty against defects in materials and workmanship. Please refer to the warranty card included with your purchase or visit the official Laserliner webසවිස්තරාත්මක වගකීම් නියමයන් සහ කොන්දේසි සඳහා අඩවිය.
For technical support, service, or spare parts, please contact your local Laserliner distributor or the customer service department. Contact information can typically be found on the Laserliner webවෙබ් අඩවිය හෝ ඔබේ නිෂ්පාදන ඇසුරුම්කරණයේ.
වගකීම් හිමිකම් සඳහා කරුණාකර ඔබගේ මිලදී ගැනීමේ සාක්ෂි තබා ගන්න.
