නිෂ්පාදනය අවසන්view
This replacement chain is specifically designed for Einhell petrol chainsaws, including models GC-PC 1335/1 I, GC-PC 1235 I, and GC-PC 1235/1. It features a length of 35 cm, 53 drive links, a drive link thickness of 1.3 mm (0.5"), and a chain pitch of 9.5 mm (3/8"). This manual provides essential information for the proper installation, operation, and maintenance of your replacement chain.
ගැළපුම
This Einhell replacement chain is compatible with the following Einhell petrol chainsaw models:
- Einhell GC-PC 1335/1 I
- Einhell GC-PC 1235 I
- Einhell GC-PC 1235/1
Ensure your chainsaw model matches one of the listed compatible models before attempting installation.
සැකසුම සහ ස්ථාපනය
ආරක්ෂාව පළමුව: Before beginning any installation or maintenance, ensure the chainsaw is turned off, the spark plug cap is removed (for petrol models), and the chain brake is engaged. Always wear appropriate personal protective equipment, including heavy-duty gloves.
- දම්වැල සකස් කරන්න: Place the chainsaw on a stable, flat surface.
- Remove the Chain Cover: Loosen and remove the nuts holding the chain cover in place. Carefully remove the chain cover and the old chain.
- Clean the Guide Bar and Sprocket: Thoroughly clean any sawdust, debris, or old oil from the guide bar groove, the sprocket, and the chain brake mechanism. Inspect the guide bar for wear or burrs.
- Install the New Chain: Carefully uncoil the new Einhell replacement chain. Ensure the cutting edges of the chain teeth are facing in the correct direction (usually indicated by an arrow on the chain or guide bar). Place the chain around the drive sprocket and then fit it into the groove of the guide bar.
- Reattach the Guide Bar and Chain Cover: Slide the guide bar back into position, ensuring the chain is properly seated in the groove. Reinstall the chain cover and hand-tighten the nuts.
- දාම ආතතිය සකසන්න: Adjust the chain tensioning screw until the chain is snug against the guide bar but can still be pulled freely by hand. The chain should not sag on the underside of the guide bar. A good rule of thumb is that you should be able to pull the chain drive links up slightly, but not enough to expose the bottom of the drive links from the guide bar groove.
- අවසාන තද කිරීම: While holding the tip of the guide bar up, fully tighten the chain cover nuts. Recheck the chain tension after tightening.
- ලිහිසි තෙල්: Ensure the chainsaw's oil reservoir is filled with appropriate chain lubricant.
Image: The Einhell replacement chainsaw chain, ready for installation. This image shows the full length of the chain, highlighting its design and the arrangement of the cutting teeth and drive links.
Operating with the New Chain
Once the new chain is installed and properly tensioned, you can operate your chainsaw. Always follow the safety guidelines provided in your chainsaw's main user manual. Key considerations for operating with a new chain include:
- දාම ලිහිසි කිරීම: Ensure the automatic oiler is functioning correctly and providing adequate lubrication to the chain and guide bar during operation.
- මූලික ධාවනය: Run the chainsaw for a few minutes at a moderate speed without cutting to allow the chain to seat properly. Recheck chain tension after this initial run and adjust if necessary, as new chains can stretch slightly.
- නිසි කැපුම් තාක්ෂණය: Always use proper cutting techniques as outlined in your chainsaw's manual to prevent kickback and ensure efficient cutting.
- Monitor Chain Condition: Regularly check the chain for sharpness, tension, and any signs of damage during use.
නඩත්තු කිරීම
Regular maintenance extends the life of your Einhell replacement chain and ensures safe and efficient operation.
- දාම තියුණු කිරීම: A sharp chain is crucial for safe and effective cutting. Sharpen the chain regularly using a round file of the correct diameter (typically 4.0 mm or 5/32" for 3/8" pitch chains, but refer to your chainsaw manual for exact specifications). Sharpen each tooth evenly.
- දාම ලිහිසි කිරීම: Always ensure the chainsaw's oil reservoir is filled with high-quality chain oil. Proper lubrication reduces friction and wear on the chain and guide bar.
- Chain Tension Check: Check chain tension frequently, especially during prolonged use. A loose chain can derail, and an overly tight chain can cause premature wear and damage to the chainsaw.
- පිරිසිදු කිරීම: After each use, clean the chain and guide bar to remove sawdust, resin, and debris. This prevents buildup that can hinder performance and cause wear.
- Inspection for Wear and Damage: Regularly inspect the chain for bent or broken links, cracks, or excessive wear on the drive links and cutting teeth. Replace the chain if significant damage is found.
දෝෂගවේෂණය
Here are some common issues and their potential solutions related to your chainsaw chain:
| ගැටලුව | විය හැකි හේතුව | විසඳුම |
|---|---|---|
| දාමය කාර්යක්ෂමව නොකැපීම / දාමය අඳුරු වීම | Dull cutting teeth, incorrect sharpening angle, hitting foreign objects. | Sharpen the chain. Ensure correct sharpening angle. Inspect for damage and replace if necessary. |
| දාමය මාර්ගෝපදේශ තීරුවෙන් ඉවතට පැමිණේ | Incorrect chain tension (too loose), worn guide bar, worn sprocket, damaged chain. | Adjust chain tension. Inspect guide bar and sprocket for wear and replace if needed. Check chain for damage. |
| දාම දුම්පානය හෝ අධික උනුසුම් වීම | ප්රමාණවත් ලිහිසිකරණය, වැරදි දාම ආතතිය (ඉතා තද), අඳුරු දාමය. | තෙල් සංචිතය සහ ඔයිලර් ක්රියාකාරිත්වය පරීක්ෂා කරන්න. දාම ආතතිය සකසන්න. දාමය තියුණු කරන්න හෝ ප්රතිස්ථාපනය කරන්න. |
| දාමය කැපුමේදී බැඳේ | Dull chain, improper cutting technique, chain tension too tight. | දාමය මුවහත් කරන්න. නැවතview කැපුම් තාක්ෂණය. දාම ආතතිය සකසන්න. |
පිරිවිතර
The Einhell Replacement Chain (Model: 4500172) features the following technical specifications:
- දාම දිග: 35 cm (අඟල් 13.78)
- Drive Links: 53
- Drive Link Thickness: 1.3 mm (අඟල් 0.05)
- දම්වැල් තණතීරුව: 9.5 mm (අඟල් 3/8)
- දාම වර්ගය: අර්ධ-චිසල්
- අයිතමයේ බර: ආසන්න වශයෙන් 6 අවුන්ස
- නිෂ්පාදන මානයන්: 3.43 x 1.38 x 6.69 අඟල් (ඇසුරුම් කර ඇත)
Image: Illustrates the chain's length of 35 cm and the count of 53 drive links, key specifications for compatibility.
Image: Depicts the drive link thickness of 1.3 mm (0.05 inches), a critical measurement for proper fit in the guide bar.
Image: Shows the chain pitch of 9.5 mm (3/8 inches), which determines the spacing between the drive links and compatibility with the chainsaw's sprocket.
වගකීම් සහ සහාය
For information regarding the warranty of your Einhell Replacement Chain or for technical support, please refer to the original chainsaw's user manual or visit the official Einhell website. Specific warranty terms and support contacts may vary by region.
නිෂ්පාදකයා: අයින්හෙල්
කොටස අංකය: 4500172
