1. හැඳින්වීම
This manual provides essential information for the safe and effective operation, setup, and maintenance of the Hilti GX120 Gas-Actuated Fastening Tool. The Hilti GX120 is a fully automatic, gas-powered fastening tool designed for high mobility and consistent fastening performance. It is suitable for attaching drywall track to concrete, concrete block, and steel surfaces. Please read this manual thoroughly before using the tool.
2 ආරක්ෂිත තොරතුරු
බල මෙවලම් ක්රියාත්මක කිරීමේදී සැමවිටම ආරක්ෂාවට ප්රමුඛත්වය දෙන්න. ආරක්ෂක උපදෙස් අනුගමනය කිරීමට අපොහොසත් වීමෙන් බරපතල තුවාල හෝ දේපළ හානි සිදුවිය හැකිය.
- පුද්ගලික ආරක්ෂක උපකරණ (PPE): Always wear appropriate PPE, including safety glasses, hearing protection, and gloves, when operating the tool.
- වැඩ කරන ප්රදේශය: Ensure the work area is clear of bystanders, well-lit, and free from obstructions.
- මෙවලම් පරීක්ෂාව: Before each use, inspect the tool for any damage, loose parts, or malfunctions. Do not use a damaged tool.
- ගෑස් කැනිස්ටර් හැසිරවීම: Handle gas canisters with care. Store them in a cool, well-ventilated area away from direct sunlight and ignition sources.
- ගාංචු තේරීම: Use only Hilti-approved fasteners and gas canisters compatible with the GX120.
- මෙවලම් මෙහෙයුම: Never point the tool at yourself or others. Keep hands and body parts away from the fastening point.
- නඩත්තු: Disconnect the gas canister and remove fasteners before performing any maintenance or cleaning.
3. සංරචක අවසන්view
The Hilti GX120 consists of several key components that facilitate its operation. Understanding these components is crucial for proper use and maintenance.
රූපය 3.1: Hilti GX120 Gas-Actuated Fastening Tool. This image displays the complete tool, highlighting its red and black casing, the gas canister compartment at the rear, the trigger handle, the magazine for fasteners, and the nosepiece where fasteners are driven.
- නාසයක්: The part of the tool that contacts the work surface and guides the fastener. It is adjustable for optimum fastening quality.
- සඟරාව: Holds the strip of fasteners.
- Gas Canister Compartment: Located at the rear, this houses the gas canister that provides the power for actuation.
- ප්රේරකය: Activates the fastening mechanism.
- හසුරුව: ග්රහණය සහ පාලනය සඳහා කාර්යක්ෂමව නිර්මාණය කර ඇත.
- Nail Punch Set: Included for specific applications.
4. පිහිටුවීම
Proper setup ensures efficient and safe operation of the Hilti GX120.
- Insert Gas Canister: Open the gas canister compartment and insert a Hilti-approved gas canister. Ensure it is securely seated.
- Load Fasteners: Insert a strip of compatible fasteners into the tool's magazine. Ensure the fasteners are correctly oriented and the strip feeds smoothly. The tool supports fastener lengths from 9/16 to 1-9/16 inches.
- Adjust Tool Nose: Use the single lever on the tool nose to adjust its depth for the specific application and material. This adjustment is critical for achieving optimum fastening quality.
- බල ගැන්වීම: The tool features an automatic electronic gas injection system. Ensure the tool is ready for operation as indicated by the tool's status lights (if applicable, refer to tool markings).
5. මෙහෙයුම් උපදෙස්
Follow these steps for safe and effective operation of the Hilti GX120.
- Prepare Work Surface: Ensure the surface is clean, dry, and free from debris. Mark fastening points as needed.
- ස්ථාන මෙවලම: Place the tool's nosepiece firmly and squarely against the work surface at the desired fastening point. Apply sufficient pressure to engage the safety mechanism.
- Actuate Tool: Press the trigger to drive the fastener. The fully automatic electronic gas injection system will ensure consistent fastening.
- මුදා හැරීම සහ නැවත ස්ථානගත කිරීම: Release the trigger and lift the tool from the surface. Reposition for the next fastening point.
- Monitor Gas and Fasteners: The tool can drive approximately 750 fasteners with a single gas can. Monitor gas levels and fastener supply to avoid interruptions.
Compatible Fastener Types: The Hilti GX120 uses fastener types X-EGN, X-GHP, and X-GN.
6. නඩත්තු කිරීම
Regular maintenance extends the life of your Hilti GX120 and ensures consistent performance.
- දෛනික පිරිසිදු කිරීම: After each use, clean the tool, especially the nosepiece and magazine area, to remove dust and debris. Use a dry cloth or brush.
- වරින් වර පරීක්ෂා කිරීම: Regularly inspect the tool for wear and tear, particularly the nosepiece, fasteners, and gas canister connections.
- ගබඩා: Store the tool in its case (included) in a dry, secure location away from extreme temperatures and unauthorized access. Remove the gas canister before long-term storage.
- වෘත්තීය සේවා: For complex repairs or internal cleaning, contact authorized Hilti service centers. Do not attempt to disassemble the tool beyond basic user-level maintenance.
7. දෝශ නිරාකරණය
This section addresses common issues you might encounter with the Hilti GX120.
| ගැටලුව | විය හැකි හේතුව | විසඳුම |
|---|---|---|
| මෙවලම ගිනි නොගනී | Empty gas canister; No fasteners in magazine; Tool not pressed firmly against surface; Safety mechanism not engaged. | Replace gas canister; Load fasteners; Apply firm pressure to the nosepiece; Ensure safety mechanism is fully engaged. |
| Inconsistent fastening depth | Incorrect nosepiece adjustment; Worn nosepiece; Low gas pressure. | Adjust nosepiece depth; Inspect and replace worn nosepiece; Replace gas canister. |
| Fasteners jam in magazine | Damaged fasteners; Debris in magazine; Incorrect fastener type. | Remove jammed fasteners and inspect for damage; Clean magazine; Ensure correct fastener type is used. |
8. පිරිවිතර
Key technical specifications for the Hilti GX120 Gas-Actuated Fastening Tool.
- අයිතම ආදර්ශ අංකය: 274638
- අයිතමයේ බර: රාත්තල් 16.86 කි
- නිෂ්පාදන මානයන්: අඟල් 17 x 5.3 x 15.4
- බලශක්ති ප්රභවය: ගෑස් බලයෙන් ක්රියාත්මක වන
- වෙළුමtage: 110 Volts (for electronic ignition system, if applicable)
- Fastener Length Range: අඟල් 9/16 සිට 1-9/16 දක්වා
- Compatible Fastener Types: X-EGN, X-GHP, X-GN
- Fasteners per Gas Can: ආසන්න වශයෙන් 750
- ඇතුළත් සංරචක: Tool, 1 GX 120 nail punch set, Z case
