1. නිෂ්පාදන අවසන්view
The Eberle KLR-E 7010 is a bimetal thermostat designed for controlling fancoil units. It provides precise temperature regulation and offers control over fan speed and operating mode (heating or cooling). This manual provides essential information for the safe and efficient installation, operation, and maintenance of your thermostat.
රූපය 1: ඉදිරිපස view of the Eberle KLR-E 7010 Fancoil Thermostat. The image displays the front panel of the thermostat, which is white with the 'EBERLE' brand name in the top left. On the right side, there is a large rotary dial for temperature setting, marked in degrees Celsius from 5 to 30. An arrow indicates the current setpoint. On the left, there are two horizontal slide switches. The top switch controls the fan speed, with icons representing different fan speeds. The bottom switch selects between heating (wavy lines), off (center), and cooling (snowflake) modes.
2. වැදගත් ආරක්ෂක උපදෙස්
- Always disconnect power to the fancoil unit and thermostat at the main circuit breaker before performing any installation, wiring, or maintenance.
- Installation and wiring must be performed by a qualified electrician in accordance with all local and national electrical codes.
- Do not operate the thermostat with wet hands or when standing on a wet surface.
- විදුලි අනතුරු වළක්වා ගැනීම සඳහා සියලුම රැහැන් සම්බන්ධතා ආරක්ෂිතව සහ නිසි ලෙස පරිවරණය කර ඇති බවට සහතික වන්න.
- This device is designed for indoor use only. Do not expose it to moisture, extreme temperatures, or direct sunlight.
- Keep the thermostat away from children and pets.
3. ස්ථාපන මාර්ගෝපදේශය
3.1. පැකේජ අන්තර්ගතය
ස්ථාපනය ආරම්භ කිරීමට පෙර සියලුම සංරචක පවතින බව තහවුරු කර ගන්න:
- Eberle KLR-E 7010 Fancoil Thermostat unit
- Mounting screws (typically included with the unit)
- උපදෙස් අත්පොත (මෙම ලේඛනය)
3.2. සවි කිරීමේ උපදෙස්
- ස්ථානය තෝරන්න: Choose an interior wall location, approximately 1.5 meters (5 feet) above the floor, away from direct sunlight, drafts, heat sources, or areas with poor air circulation.
- බලය විසන්ධි කරන්න: Turn off the power to the fancoil unit at the main circuit breaker. Verify that power is off using a voltagඊ පරීක්ෂක.
- Separate Base Plate: Carefully separate the front cover of the thermostat from its base plate.
- සවිකිරීමේ පාදක තහඩුව: Position the base plate on the wall and mark the drilling locations. Drill holes and insert wall anchors if necessary. Secure the base plate to the wall using the provided mounting screws.
- රැහැන් ඇදීම: Refer to the wiring diagram (Section 3.3) and connect the electrical wires to the appropriate terminals on the base plate. Ensure all connections are tight and correct.
- Attach Front Cover: Once wiring is complete and verified, carefully reattach the front cover to the base plate, ensuring it clicks securely into place.
- බලය ප්රතිස්ථාපනය කරන්න: ප්රධාන පරිපථ කඩනයෙහි විදුලිය නැවත ක්රියාත්මක කරන්න.
3.3. රැහැන් සටහන
The Eberle KLR-E 7010 thermostat is designed for 230 Volts systems. Due to variations in fancoil unit configurations and local electrical codes, a generic wiring diagram cannot be provided here. It is imperative that a qualified electrician performs all wiring to ensure proper functionality and safety. The electrician should consult the specific wiring instructions provided with your fancoil unit and the terminal markings on the thermostat's base plate.
4. මෙහෙයුම් උපදෙස්
4.1. පාලනය කරයිview
The thermostat features three primary controls:
- උෂ්ණත්ව ඩයල්: A large rotary dial on the right side of the unit, marked in degrees Celsius, used to set the desired room temperature.
- විදුලි පංකා වේග ස්විචය: A horizontal slide switch on the upper left, typically with three fan blade icons, allowing selection of low, medium, or high fan speed.
- Mode Selection Switch: A horizontal slide switch on the lower left, used to select between heating (wavy lines), cooling (snowflake), or off (center) modes.
4.2. උෂ්ණත්වය සැකසීම
To set the desired room temperature, rotate the large dial clockwise or counter-clockwise until the indicator arrow points to your preferred temperature in degrees Celsius. The thermostat will then work to maintain this temperature.
4.3. පංකා වේග පාලනය
Use the upper left slide switch to adjust the fancoil's fan speed:
- අඩු: For quiet operation and minimal air circulation.
- මධ්යම: A balanced setting for general comfort.
- ඉහළ: For rapid temperature change or maximum air circulation.
4.4. Mode Selection (Heating/Cooling)
Use the lower left slide switch to select the operating mode:
- Heating (wavy lines): The thermostat will activate the heating function when the room temperature falls below the setpoint.
- අක්රිය (මැද ස්ථානය): The fancoil unit will remain off, regardless of temperature.
- Cooling (snowflake): The thermostat will activate the cooling function when the room temperature rises above the setpoint.
5. නඩත්තු කිරීම
The Eberle KLR-E 7010 thermostat requires minimal maintenance.
- පිරිසිදු කිරීම: Periodically wipe the exterior of the thermostat with a soft, dry cloth to remove dust. Do not use abrasive cleaners, solvents, or spray directly onto the unit.
- පරිශීලක-සේවා කළ හැකි කොටස් නොමැත: The thermostat contains no user-serviceable parts. Do not attempt to open or repair the unit yourself. Refer all servicing to qualified personnel.
6. දෝශ නිරාකරණය
If you experience issues with your Eberle KLR-E 7010 thermostat, consult the table below for common problems and potential solutions.
| ගැටලුව | විය හැකි හේතුව | විසඳුම |
|---|---|---|
| Thermostat not responding / No power | No power at the circuit breaker; Loose wiring connection. | Check the circuit breaker and ensure it is in the 'ON' position. Verify all wiring connections are secure (consult a qualified electrician). |
| Fancoil not heating/cooling | Incorrect mode selected; Temperature setpoint too high/low; Fancoil unit malfunction. | Ensure the mode switch is set to 'Heating' or 'Cooling' as desired. Adjust the temperature setpoint appropriately. Check the fancoil unit for operational issues. |
| විදුලි පංකාව ක්රියා නොකරයි | Fan speed switch set to 'Off' (if applicable); Fancoil unit fan malfunction. | Ensure the fan speed switch is set to a desired speed (Low, Medium, or High). Check the fancoil unit's fan for issues. |
| වැරදි උෂ්ණත්ව කියවීම් | Thermostat located near heat/cold source or draft. | Relocate the thermostat to a more suitable position if possible, away from direct influences. |
If the problem persists after attempting these solutions, contact a qualified technician or customer support.
7. තාක්ෂණික පිරිවිතර
- වෙළඳ නාමය: Eberle
- ආකෘතිය: KLR-E 7010
- වර්ගය: Bimetal Fancoil Thermostat
- වෙළුමtage: වෝල්ට් 230
- මානයන් (L x W x H): 11.71 x 7.11 x 2.69 සෙ.මී. (ආසන්න වශයෙන් 4.61 x 2.80 x 1.06 අඟල්)
- බර: ග්රෑම් 120 (ආසන්න වශයෙන් රාත්තල් 0.26)
- විදුලි පංකා පාලනය: 3-speed fan selector
- මාදිලි පාලනය: Heating/Cooling/Off selector
- උෂ්ණත්ව පරාසය: Typically 5°C to 30°C (41°F to 86°F)
- බැටරි: Not required, not included
- නිෂ්පාදක යොමුව: 3024146
- ලිපි මාදිලි අංකය: 8402414979620
8. වගකීම් තොරතුරු
This Eberle KLR-E 7010 thermostat is covered by the manufacturer's standard warranty. The specific terms and duration of the warranty may vary by region and retailer. Please retain your proof of purchase for warranty claims. For detailed warranty information, refer to the documentation provided at the time of purchase or contact your retailer.
9. පාරිභෝගික සහාය
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the retailer from whom you purchased the product or visit the official Eberle website for support contact information. When contacting support, please have your product model (KLR-E 7010) and proof of purchase readily available.
