හිල්ටි සීපී 606 ෆයර්ස්ටොප් සීලන්ට් උපදෙස් අත්පොත

1. නිෂ්පාදන අවසන්view

The Hilti CP 606 Firestop Sealant is a high-performance, intumescent acrylic sealant designed for firestopping applications. It expands when exposed to heat, forming a fire-resistant barrier that helps prevent the spread of fire and smoke through penetrations in fire-rated constructions. This product is suitable for various joint and penetration sealing applications in walls and floors.

An image showing a single 10.5oz tube of Hilti CP 606 red firestop sealant, clearly displaying the Hilti logo and product identification.

2 ආරක්ෂිත තොරතුරු

Always prioritize safety when working with sealants. Read and understand the Safety Data Sheet (SDS) before use. Observe all local safety regulations.

• පුද්ගලික ආරක්ෂක උපකරණ (PPE): Wear appropriate PPE, including safety glasses, gloves, and protective clothing, to prevent skin and eye contact.
• වාතාශ්රය: Use in well-ventilated areas. If adequate ventilation is not available, use respiratory protection.
• සම සම්බන්ධතා: සම ස්පර්ශ වන විට, සබන් හා ජලය සමග හොඳින් සේදීම.
• අක්ෂි සම්බන්ධතා: In case of eye contact, flush immediately with plenty of water for several minutes and seek medical attention.
• ශරීරගත කිරීම: ගිල දමන්න එපා. ගිල දැමුවහොත් වහාම වෛද්‍ය ප්‍රතිකාර ලබා ගන්න.
• ළඟා විය නොහැකි ලෙස තබා ගන්න: ළමයින්ට සහ සුරතල් සතුන්ට ළඟාවිය නොහැකි ලෙස තබා ගන්න.

3. සැකසීම සහ සකස් කිරීම

1. මතුපිට සකස් කිරීම: Ensure all surfaces to be sealed are clean, dry, and free from dust, oil, grease, loose particles, and other contaminants. Substrates should be sound and stable.
2. Joint Dimensions: Verify that joint dimensions are within the product's specified limits for optimal performance.
3. ආධාරක ද්‍රව්‍ය: For deeper joints, use a suitable backing material (e.g., backer rod) to control sealant depth and ensure proper sealant geometry.
4. අවශ්ය මෙවලම්:
   • Standard caulking gun
   • Utility knife or sealant cutter
   • Trowel or tooling stick for finishing
   • Cleaning supplies (rags, appropriate solvent if needed)
5. උෂ්ණත්වය: Apply the sealant within the recommended temperature range, typically between 5°C and 40°C (41°F and 104°F).

4. යෙදුම් උපදෙස්

1. කාට්රිජ් සකස් කරන්න: Cut the tip of the sealant tube at a 45-degree angle to the desired bead size. Puncture the inner seal of the cartridge.
2. කෝල්කින් තුවක්කුව පැටවීම: Insert the prepared cartridge into a standard caulking gun.
3. සීලන්ට් යොදන්න: Apply the sealant evenly and continuously into the joint or penetration, ensuring full contact with the substrate. Maintain consistent pressure on the trigger to achieve a smooth, uniform bead.
4. මෙවලම්: Within 5-10 minutes of application (before skinning occurs), tool the sealant to ensure good adhesion and a smooth finish. Remove any excess sealant immediately.
5. සුව කිරීම: The sealant will skin over in approximately 15-30 minutes, depending on temperature and humidity. Full cure time can range from several days to weeks, depending on bead thickness and environmental conditions. Protect the freshly applied sealant from water and heavy traffic until fully cured.

5. නඩත්තු කිරීම

Once cured, Hilti CP 606 Firestop Sealant requires minimal maintenance. Periodically inspect sealed joints and penetrations for any signs of damage, cracking, or degradation. If damage is observed, clean the area and reapply sealant as necessary to maintain the firestop integrity.

6. දෝශ නිරාකරණය

• දුර්වල ඇලවීම:

  Ensure surfaces are clean, dry, and free of contaminants. Proper surface preparation is critical for good adhesion.
• මන්දගාමී සුව කිරීම:

  Low temperatures and high humidity can extend curing times. Ensure adequate ventilation and maintain recommended application temperatures.

• Cracking or Shrinkage:

  Excessive joint movement or improper joint design can lead to cracking. Ensure correct joint dimensions and use of backing material where appropriate.

7. පිරිවිතර

8. ගබඩා කිරීම සහ බැහැර කිරීම

• ගබඩා: Store the sealant in its original, unopened packaging in a cool, dry place, away from direct sunlight and extreme temperatures. Recommended storage temperature is typically between 5°C and 25°C (41°F and 77°F).
• බැහැර කිරීම: Dispose of unused product and empty containers in accordance with local, state, and federal regulations. Do not dispose of in drains or waterways. Consult local waste management authorities for proper disposal methods.

9. වගකීම් සහ සහාය

For specific warranty information regarding the Hilti CP 606 Firestop Sealant, please refer to the official Hilti website or contact Hilti customer service directly. Hilti provides comprehensive technical support and product documentation to assist with proper application and performance.

හිල්ටි නිල Webඅඩවිය: www.hilti.com