1. නිෂ්පාදන අවසන්view
The Hormann HSE4 868 BS BiSecur remote control is a 4-channel handheld transmitter designed for operating up to four different Hormann drives or functions. It features a modern design with a black textured plastic surface and chrome-plated die-cast zinc caps. This remote control is equipped with BiSecur technology, ensuring secure transmission, and is also backward compatible with older Hormann drives operating at 868.3 MHz (Series 1, 2, and 3, provided a Hormann 868 MHz receiver is present for Series 1).
ප්රධාන ලක්ෂණ ඇතුළත් වේ:
- නාලිකා 4: Control up to four distinct functions or devices.
- BiSecur Technology: High-quality, secure signal transmission.
- පසුගාමී අනුකූලතාව: Works with older Hormann 868.3 MHz transmitters (e.g., HS1/HS2/HS4 868, HSE2 868, HSM2/HSM4 868, HSP4/HSP4-C 868, HSD2-C/HSD2-A 868, HSZ1/HSZ2 868).
- පහසු වැඩසටහන්කරණය: Simple remote programming procedure, no special equipment required.
- ඇතුළත් වේ: Battery (3V lithium button cell, type CR 2032) and a keyring for convenience.
- පරාසය: Up to 100 meters (actual range may vary depending on local conditions).
Figure 1: Hormann HSE4 868 BS BiSecur Remote Control.
2. සැකසුම සහ ක්රමලේඛනය
This section outlines the general procedure for programming your new Hormann HSE4 868 BS BiSecur remote control. The remote features a self-learning function for easy setup.
2.1. Pairing with a BiSecur Receiver (Newer Systems)
- ලබන්නා සූදානම් කරන්න: Locate the programming button on your Hormann drive's receiver unit. The exact location may vary by model (refer to your drive's manual).
- ඉගෙනුම් මාදිලිය සක්රිය කරන්න: Press and hold the programming button on the receiver until the LED indicator on the receiver starts flashing (usually red). This indicates the receiver is in learning mode.
- Transmit Signal from New Remote: Take your new HSE4 868 BS remote control. Press and hold the desired button on the new remote that you wish to program.
- යුගල කිරීම තහවුරු කරන්න: Keep the button on the new remote pressed. The LED on the receiver should change its flashing pattern or illuminate steadily to confirm successful pairing. Release the button on the remote.
- පරීක්ෂණ ක්රියාකාරීත්වය: Press the programmed button on your new remote to test if the drive responds correctly.
2.2. Copying from an Existing BiSecur Remote (Transmitter-to-Transmitter)
You can also copy the code from an existing, working BiSecur remote control to your new HSE4 868 BS remote.
- ස්ථාන දුරස්ථ පාලක: Place the existing (master) remote and the new HSE4 868 BS remote close to each other, ideally touching or within a few centimeters.
- Activate Learning Mode on New Remote: Press and hold the button on the new HSE4 868 BS remote that you wish to program. The LED on the new remote will flash slowly.
- Transmit Code from Master Remote: While still holding the button on the new remote, press and hold the corresponding button on the existing (master) remote.
- Confirm Copy: The LED on the new remote will flash faster, then illuminate steadily to indicate successful code transfer. Release both buttons.
- පරීක්ෂණ ක්රියාකාරීත්වය: Test the newly programmed button on your HSE4 868 BS remote with your drive.
සටහන: For older Hormann drives (Series 1, 2, 3) operating at 868.3 MHz (with blue buttons on older remotes), the HSE4 868 BS can be switched to a fixed code mode if necessary. Refer to the specific instructions for your drive model if you encounter compatibility issues.
3. මෙහෙයුම් උපදෙස්
The Hormann HSE4 868 BS remote control features four distinct buttons, allowing you to control up to four different functions or devices.
- බොත්තම් කාර්යයන්: Each of the four buttons can be programmed independently to operate a specific garage door, gate, or other compatible Hormann device.
- Impulse Function: Pressing a programmed button will send an impulse signal to the receiver, typically initiating an open/stop/close cycle for a garage door or gate.
- LED දර්ශකය: A small LED on the remote will illuminate briefly when a button is pressed, indicating that a signal is being transmitted. If the LED does not light up or is dim, the battery may need replacement.
Ensure you are within the operational range (up to 100 meters, depending on environmental factors) of your receiver for reliable operation.
4. නඩත්තු කිරීම
Proper maintenance ensures the longevity and reliable operation of your remote control.
4.1. බැටරි ප්රතිස්ථාපනය
The remote control is powered by a 3V lithium button cell battery, type සීආර් 2032.
- බැටරි මැදිරිය හඳුනා ගන්න: The battery compartment is typically located on the back or side of the remote. You may need a small screwdriver or coin to open it.
- පැරණි බැටරිය ඉවත් කරන්න: Carefully remove the old CR 2032 battery. Note its polarity (+/-).
- නව බැටරිය ඇතුළු කරන්න: Insert a new CR 2032 battery, ensuring the correct polarity.
- වසා දැමීමේ මැදිරිය: බැටරි මැදිරිය ආරක්ෂිතව වසා දමන්න.
- පරීක්ෂණය: Test the remote control to ensure it functions correctly.
බැහැර කිරීම: දේශීය රෙගුලාසි වලට අනුව භාවිතා කළ බැටරි බැහැර කරන්න. ගෘහස්ථ අපද්රව්යවලට බැටරි බැහැර නොකරන්න.
4.2. පිරිසිදු කිරීම සහ ගබඩා කිරීම
- මෘදු වියළි රෙද්දකින් දුරස්ථ පාලකය පිරිසිදු කරන්න. උල්ෙල්ඛ පිරිසිදු කරන්නන් හෝ ද්රාවක භාවිතා නොකරන්න.
- The remote is designed for dry environments only. Avoid exposure to moisture, rain, or extreme temperatures (-20°C to +60°C).
- Store the remote in a safe place where it will not be accidentally activated or damaged.
5. දෝශ නිරාකරණය
If your Hormann HSE4 868 BS remote control is not functioning as expected, refer to the following troubleshooting tips:
| ගැටලුව | විය හැකි හේතුව | විසඳුම |
|---|---|---|
| Remote does not operate the drive. |
|
|
| දුරස්ථ පාලකයේ LED දැල්වෙන්නේ නැත. |
|
|
| දුරස්ථ පරාසය දුර්වලයි. |
|
|
| Remote does not work with older 868.3 MHz drive. |
|
|
6. තාක්ෂණික පිරිවිතර
| ආදර්ශ අංකය | TR-424 |
| සංඛ්යාතය | 868.3 MHz (BiSecur) |
| නාලිකා | 4 |
| කේතනය කිරීම | BiSecur, self-learning, fixed code possible for 868 MHz |
| බැටරි වර්ගය | 3V Lithium Button Cell, CR 2032 |
| මානයන් (W x H x D) | 28 mm x 70 mm x 14 mm |
| ආරක්ෂණ වර්ගය | For dry rooms only |
| උෂ්ණත්ව පරාසය | -20 ° C සිට +60 ° C |
| පරාසය | Approx. 30-100 meters (depending on local conditions) |
| නිෂ්පාදකයා | හෝර්මන් |
| මුල් රට | ජර්මනිය |
7. වගකීම් සහ සහාය
Specific warranty information for the Hormann HSE4 868 BS BiSecur remote control is not provided in the product details. For warranty claims, technical support, or further assistance, please contact your Hormann dealer or the point of purchase. Keep your proof of purchase for any warranty-related inquiries.
Information regarding spare parts availability is also not explicitly provided. For spare parts, please contact Hormann customer service or an authorized dealer.
