Axxess AXTOYCAM26V

Axxess AX-TOYCAM2-6V Toyota Backup Camera Retention and Add-On Interface Manual

ආකෘතිය: AXTOYCAM26V | වෙළඳ නාමය: පොරව

1. හැඳින්වීම

The Axxess AX-TOYCAM2-6V is an interface designed to facilitate the retention of a factory backup camera or the addition of an aftermarket backup camera in select Toyota vehicles. This module includes an AX-CAM6V 12-volt to 6-volt converter, ensuring compatibility with factory camera systems that operate on a lower voltage. This manual provides essential information for proper installation, operation, and maintenance of the device.

2 ආරක්ෂිත තොරතුරු

  • Always disconnect the vehicle's negative battery terminal before beginning any installation to prevent electrical shorts and damage.
  • ප්‍රශස්ත කාර්ය සාධනය සහ ආරක්ෂාව සඳහා වෘත්තීය ස්ථාපනය නිර්දේශ කෙරේ.
  • කෙටි පරිපථ වැළැක්වීම සඳහා සියලුම සම්බන්ධතා ආරක්ෂිතව සහ නිසි ලෙස පරිවරණය කර ඇති බවට සහතික වන්න.
  • Do not modify the harness or components unless explicitly instructed. Unauthorized modifications can void the warranty and cause damage.
  • Route all wiring away from moving parts, heat sources, and sharp edges to prevent damage.

3. පැකේජ අන්තර්ගතය

ස්ථාපනය සමඟ ඉදිරියට යාමට පෙර සියලුම අයිතම පවතින බව තහවුරු කරගන්න:

  • Axxess AX-TOYCAM2-6V Interface Harness
  • AX-CAM6V 12-volt to 6-volt Converter

The image below displays the main components of the AX-TOYCAM2-6V harness.

Axxess AX-TOYCAM2-6V Toyota Backup Camera Retention and Add-On Interface Harness

This image displays the Axxess AX-TOYCAM2-6V harness, featuring multiple connectors for integration with a Toyota vehicle's wiring system and an RCA connector for a backup camera. The harness includes red and black wires for power and ground connections, and a separate 6-volt converter.

4. පිහිටුවීම සහ ස්ථාපනය

This section outlines the general steps for installing the AX-TOYCAM2-6V interface. Specific vehicle wiring diagrams and disassembly instructions should be consulted for your particular Toyota model.

4.1 පූර්ව ස්ථාපන පියවර

  1. බැටරිය විසන්ධි කරන්න: වාහනයේ බැටරියේ ඍණ අග්‍රය විසන්ධි කරන්න.
  2. වාහන රැහැන් ඇදීම සඳහා ප්‍රවේශය: Carefully remove the necessary trim panels and the factory head unit to gain access to the vehicle's wiring harness.

4.2 පටි සම්බන්ධතාවය

  1. Connect Interface Harness: Connect the AX-TOYCAM2-6V harness to the corresponding factory connectors behind the head unit. Ensure all connections are firm and secure.
  2. Connect 6-Volt Converter (AX-CAM6V): If retaining a factory camera or adding a camera requiring 6V, connect the AX-CAM6V converter. The typical wiring for the converter is:
    • නිල්/සුදු වයර්: 12V Input (Connect to a switched 12V source).
    • Blue/Red Wire: 6V Output (Connect to the camera's 6V power input).
    • කළු වයර්: Ground (Connect to a reliable chassis ground).
  3. Connect Camera (if adding): Connect the aftermarket backup camera's video output (RCA) to the yellow RCA input on the AX-TOYCAM2-6V harness.

4.3 ස්ථාපන පියවරෙන් පසු

  1. පරීක්ෂණ ක්‍රියාකාරීත්වය: Reconnect the vehicle's battery. Turn on the ignition and engage reverse gear to test the backup camera display. Verify that the image is clear and activates correctly.
  2. නැවත එකලස් කරන්න: Once functionality is confirmed, carefully reassemble all removed trim panels and secure the head unit.

The following video demonstrates the physical appearance of the harness, which can assist in identifying components during installation.

මෙම වීඩියෝව අංශක 360ක දර්ශනයක් සපයයි view of the Axxess AX-TOYCAM2-6V harness, showcasing its various connectors and wiring. It helps in identifying the components included in the package and understanding its physical form factor.

5. මෙහෙයුම් උපදෙස්

The Axxess AX-TOYCAM2-6V interface operates automatically. Once correctly installed, the connected backup camera will display its image on the vehicle's screen when the transmission is shifted into reverse gear. No manual intervention is required for its basic operation.

6. නඩත්තු කිරීම

The AX-TOYCAM2-6V is a low-maintenance electronic component. To ensure its longevity and reliable performance:

  • සියලුම රැහැන් සම්බන්ධතා ආරක්ෂිතව සහ විඛාදනයෙන් තොරව පවතින බව සහතික කිරීම සඳහා වරින් වර පරීක්ෂා කරන්න.
  • මොඩියුලය අධික උෂ්ණත්වයට හෝ තෙතමනයට නිරාවරණය කිරීමෙන් වළකින්න.
  • Do not attempt to open or service the module yourself. Refer to qualified technicians for any issues beyond basic troubleshooting.

7. දෝශ නිරාකරණය

If you encounter issues with your backup camera system after installing the AX-TOYCAM2-6V, consider the following troubleshooting steps:

7.1 No Camera Display

  • බලය පරීක්ෂා කරන්න: Ensure the 12V input to the AX-CAM6V converter is receiving power when the vehicle is in reverse. Verify the ground connection.
  • සම්බන්ධතා තහවුරු කරන්න: Double-check all harness connections to the factory wiring and the camera's RCA input.
  • කැමරා ක්‍රියාකාරීත්වය: Test the backup camera directly if possible, to rule out a faulty camera.

7.2 Distorted or Intermittent Image

  • Inspect RCA Cable: Ensure the RCA video cable is not damaged, pinched, or routed near high-voltage wires that could cause interference.
  • ආරක්ෂිත සම්බන්ධතා: Confirm all video connections are tight and free from corrosion.
  • බල ස්ථායිතාව: Verify that the 6V output from the AX-CAM6V converter is stable.

If problems persist after performing these checks, contact Axxess technical support or a qualified installer.

8. පිරිවිතර

විශේෂාංගයවිස්තර
ආදර්ශ අංකයAXTOYCAM26V
නිෂ්පාදන මානයන්අඟල් 5 x 3 x 1
අයිතමයේ බරඅවුන්ස 3.2 කි
වෙළඳ නාමයපොරව
නිෂ්පාදකයාAXXESS MOBILITY
ගැළපෙන උපාංගනිරීක්ෂණය කරන්න
ස්ථාපන වර්ගයමතුපිට සවි කිරීම
වෙළුමtage12 Volts (Input), 6 Volts (Output via converter)
සම්බන්ධක වර්ගයHDMI, DC power (for camera, via RCA)

9. වගකීම් තොරතුරු

Axxess products are covered by a manufacturer's warranty. For specific details regarding the warranty period, coverage, and claims process for the AX-TOYCAM2-6V, please refer to the warranty documentation included with your purchase or visit the official Axxess webවෙබ් අඩවිය. වගකීම් වලංගු කිරීම සඳහා ඔබේ මිලදී ගැනීමේ සාක්ෂි තබා ගන්න.

10. සහාය

For technical assistance, installation questions, or further support regarding the Axxess AX-TOYCAM2-6V, please contact Axxess customer support directly. You can typically find contact information on the Axxess webඅඩවියේ හෝ නිෂ්පාදන ඇසුරුම්වල.

Axxess Official Webඅඩවිය: https://axxessinterfaces.com/ (Please note: This is a general placeholder link, verify the current official support website for Axxess.)

අදාළ ලියකියවිලි - AXTOYCAM26V

පෙරview Subaru 2015-Up උපස්ථ කැමරා රඳවා තබා ගැනීම සඳහා Axxess AX-SUB5RVC-6V ස්ථාපන උපදෙස්
2015 දී සහ පසුව අඟල් 7 තිර සහිත සුබාරු වාහනවල කර්මාන්තශාලා කැමරාව රඳවා තබා ගැනීමට ඉඩ සලසන Axxess AX-SUB5RVC-6V උපස්ථ කැමරා ඇඩැප්ටරය සඳහා සවිස්තරාත්මක ස්ථාපන මාර්ගෝපදේශය. රැහැන් උපදෙස් සහ වාහන අනුකූලතාව ඇතුළත් වේ.
පෙරview Axxess වාහන ඒකාබද්ධ කිරීමේ නිෂ්පාදන
ඩිජිටල් සංඥා සකසනයන්, කැමරා රඳවා ගැනීමේ පද්ධති සහ සුක්කානම් රෝද පාලන අතුරුමුහුණත් ඇතුළුව Axxess හි පුළුල් පරාසයක වාහන ඒකාබද්ධ කිරීමේ විසඳුම් ගවේෂණය කරන්න. කර්මාන්තශාලා ක්‍රියාකාරීත්වයන් රඳවා ගනිමින් ඔබේ මෝටර් රථ ශ්‍රව්‍ය අත්දැකීම වැඩි දියුණු කරන්න.
පෙරview AXXESS TYTO-01 ටොයොටා Amplified අතුරුමුහුණත ස්ථාපන උපදෙස්
AXXESS TYTO-01 සඳහා සවිස්තරාත්මක ස්ථාපන උපදෙස් ampටොයොටා සහ ලෙක්සස් වාහන සඳහා නිර්මාණය කරන ලද (2001 සිට) කර්මාන්තශාලාව සහිත lified අතුරුමුහුණත. amplified systems. Covers interface features, components, vehicle compatibility, required tools, connection wiring, installation steps, and testing procedures.
පෙරview Axxess AX-ADBOX1 Series Main Interface Control Box Installation Instructions
Installation instructions for the Axxess AX-ADBOX1 Series main interface control box, detailing features, applications, interface components, tools required, and connection steps for various vehicle models.
පෙරview Axxess AX-MAZCAM-6V Installation Guide for Mazda Backup Camera
Detailed installation instructions for the Axxess AX-MAZCAM-6V backup camera harness, enabling retention of factory cameras or addition of aftermarket cameras in select 2007-2015 Mazda vehicles.
පෙරview Axxess AX-ADFD01: Ford RSE/SYNC/THX Retention Interface Installation Guide
This document provides detailed installation instructions for the Axxess AX-ADFD01 interface, enabling retention of Ford RSE, SYNC, and THX audio systems in compatible vehicles. It covers wiring, connections, initialization, and feature usage for models from 2007 onwards.