1. නිෂ්පාදන අවසන්view
The EBARA AGA 0.75 M is a robust single-phase self-priming electric pump constructed from cast iron, designed for efficient clean water transfer. Its applications include domestic water pressure boosting, small-scale garden irrigation, vehicle washing, and general water movement tasks.
This image shows the EBARA AGA 0.75 M self-priming pump, featuring a blue cast iron body and an integrated electric motor with a black terminal box on top. The pump has visible inlet and outlet connections.
2. පිහිටුවීම සහ ස්ථාපනය
Proper installation is crucial for the pump's performance and longevity. Follow these general guidelines:
- ස්ථානගත කිරීම: Install the pump in a dry, well-ventilated area, protected from frost and direct sunlight. Ensure a stable, level surface to minimize vibration.
- නල සම්බන්ධතා: Connect the suction pipe to the pump's G1 suction port and the delivery pipe to the G1 delivery port. Ensure all connections are airtight to prevent air ingress, which can affect priming. Use appropriate sealants and fittings.
- විදුලි සම්බන්ධතාවය: The pump operates on 230 V ± 10% 50 Hz single-phase power. Connect the pump to a suitable electrical supply according to local regulations. Ensure the circuit is protected by a permanent capacitor and an automatic reset thermal-amperometric protection device.
- ප්රාථමිකකරණය: As a self-priming pump, it can draw water from a certain depth (up to 8m). Before initial startup, fill the pump body completely with clean water through the priming port until it overflows. This ensures the pump can establish suction.
3. මෙහෙයුම් උපදෙස්
Once installed and primed, the pump is ready for operation:
- ආරම්භක ආරම්භය: After priming, switch on the power supply. The pump should start drawing water and build pressure.
- අධීක්ෂණය: Observe the pump during operation. Listen for unusual noises and check for leaks. Ensure consistent water flow and pressure.
- අඛණ්ඩ මෙහෙයුම: The pump is designed for continuous duty within its specified operating limits. Avoid running the pump dry, as this can cause damage to the mechanical seal.
- වසා දමන්න: To stop the pump, simply switch off the power supply.
4. නඩත්තු කිරීම
Regular maintenance helps ensure the longevity and efficient operation of your pump:
- නිතිපතා පරීක්ෂා කිරීම: Periodically check all connections for leaks and ensure the pump is securely mounted. Inspect the power cable for any damage.
- පිරිසිදු කිරීම: Keep the pump exterior clean and free from debris. Ensure the motor's ventilation fins are not obstructed to prevent overheating.
- ශීත ඍතුව (අදාළ නම්): In areas prone to freezing temperatures, drain the pump completely to prevent damage from ice expansion. Disconnect pipes and open drain plugs. Store the pump in a frost-free environment if possible.
- යාන්ත්රික මුද්රාව: The mechanical seal is a wear part. If persistent leaks occur from the shaft area, the seal may need replacement by a qualified technician.
5. දෝශ නිරාකරණය
මෙම කොටසින් ඔබට මුහුණ දීමට සිදුවිය හැකි පොදු ගැටළු සාකච්ඡා කෙරේ:
| ගැටලුව | විය හැකි හේතුව | විසඳුම |
|---|---|---|
| පොම්පය ආරම්භ නොවේ | No power supply; Motor overload protection tripped; Seized impeller | Check power connection and circuit breaker; Allow motor to cool and reset protection; Contact qualified technician. |
| පොම්පය ක්රියාත්මක වන නමුත් ජල ප්රවාහයක් නොමැත | Pump not primed; Air leak in suction line; Suction lift too high; Clogged suction filter | Re-prime the pump; Check all suction connections for leaks; Ensure suction depth is within 8m limit; Clean suction filter. |
| Low pressure or reduced flow | Partial air leak; Partially clogged impeller/pipes; Worn impeller or mechanical seal | Check suction line for small leaks; Inspect and clean impeller/pipes; Contact qualified technician for inspection. |
| අධික ශබ්දය හෝ කම්පනය | කුහරය (ජලයේ වාතය); ලිහිල් සවි කිරීම; ෙබයාරිං ඇඳුම් | Ensure proper priming and no air leaks; Securely fasten pump; Contact qualified technician. |
6. පිරිවිතර
| විශේෂාංගය | විස්තර |
|---|---|
| නිෂ්පාදකයා | Ebara |
| ආදර්ශ අංකය | 1100090000 |
| ද්රව්ය | වාත්තු යකඩ |
| බලශක්ති ප්රභවය | රැහැන්ගත විදුලි |
| වෙළුමtage | Volts 230 (AC) |
| උපරිම මෙහෙයුම් පීඩනය | 6 බාර් |
| උපරිම දියර උෂ්ණත්වය | 45 °C |
| උපරිම චූෂණ ගැඹුර | මීටර් 8 |
| චූෂණ සම්බන්ධතාවය | G1 |
| Delivery Connection | G1 |
| මෝටර් කාර්යක්ෂමතාව | IE2 and IE3 (from 0.75 kW) |
| පරිවාරක පන්තිය | F |
| ආරක්ෂණ උපාධිය | IP44 |
| පැකේජ මානයන් | 40.5 x 18.5 x 18 සෙ.මී |
| අයිතමයේ බර | කිලෝ ග්රෑම් 12.5 කි |
| බැටරි ඇතුළත් | නැත |
| අවශ්ය බැටරි | නැත |
| අමතර කොටස් ලබා ගැනීමේ හැකියාව | තොරතුරු නොමැත |
7. වගකීම් සහ සහාය
For warranty information and technical support, please refer to the documentation provided with your purchase or contact your authorized Ebara dealer. Information regarding spare parts availability is currently not provided in the product specifications.
