හැඳින්වීම
This manual provides detailed instructions for the safe and efficient operation of your Delock 86108 Network Cable Tester. This device is designed to test various cable types, including RJ45, RJ12, BNC, and USB, for continuity and correct wiring, ensuring reliable network and data connections.
ආරක්ෂිත උපදෙස්
- Read all instructions thoroughly before using the device.
- Do not expose the device to moisture, liquids, or extreme temperatures.
- Use only the specified 9V battery type. Incorrect battery usage may damage the device.
- උපාංගය ඔබම විවෘත කිරීමට හෝ අලුත්වැඩියා කිරීමට උත්සාහ නොකරන්න. සියලුම සේවා සුදුසුකම් ලත් පුද්ගලයින් වෙත යොමු කරන්න.
- උපාංගය දරුවන්ට ළඟාවිය නොහැකි ලෙස තබා ගන්න.
පැකේජයේ අන්තර්ගතය
- Delock 86108 Network Cable Tester (Main Unit)
- දුරස්ථ ඒකකය
- පරිශීලක අත්පොත (මෙම ලේඛනය)
සටහන: බැටරි ඇතුළත් නොවන අතර වෙන වෙනම මිලදී ගත යුතුය.
නිෂ්පාදනය අවසන්view
The Delock 86108 Network Cable Tester consists of a main unit and a detachable remote unit. It features an integrated LED display for indicating test results for various cable types.
ප්රධාන ඒකකය
Image Description: A red and yellow Delock 86108 Network Cable Tester main unit, showing the various ports (RJ45, RJ12, BNC, USB) and the LED indicator panel. The device has a robust, handheld design.
දුරස්ථ ඒකකය
The remote unit detaches from the main unit, allowing for convenient testing of installed cables over longer distances. It typically features corresponding ports to connect the opposite end of the cable being tested.
සැලසුම
බැටරි ස්ථාපනය
- ප්රධාන ඒකකයේ පිටුපස බැටරි මැදිරිය සොයා ගන්න.
- බැටරි මැදිරි කවරය විවෘත කරන්න.
- Insert one 9V battery, ensuring correct polarity (+/-) as indicated inside the compartment.
- බැටරි මැදිරි කවරය ආරක්ෂිතව වසා දමන්න.
බල ගැන්වීම / අක්රිය කිරීම
To power on the device, slide the power switch to the "ON" position. The LED indicators will briefly illuminate as a self-test. To power off, slide the switch to the "OFF" position.
මෙහෙයුම් උපදෙස්
The Delock 86108 can test various cable types for continuity and correct wiring sequence. Always ensure the tester is powered on before connecting cables for testing.
Testing RJ45/RJ12 Cables
- Connect one end of the RJ45 or RJ12 cable to the corresponding port on the main unit.
- Connect the other end of the cable to the corresponding port on the remote unit. For installed cables, the remote unit can be detached and placed at the other end of the cable run.
- පරීක්ෂකය සක්රිය කරන්න.
- Observe the LED indicators on both the main and remote units. Each LED corresponds to a specific wire. A sequential illumination of LEDs (1-8 for RJ45, 1-6 for RJ12) on both units indicates correct wiring and continuity.
- If an LED does not light up, it indicates an open circuit (broken wire).
- If LEDs light up out of sequence, it indicates a wiring fault (e.g., crossed pairs, short circuit).
Testing BNC Cables
- Connect one end of the BNC cable to the BNC port on the main unit.
- Connect the other end of the BNC cable to the BNC port on the remote unit.
- පරීක්ෂකය සක්රිය කරන්න.
- The LED indicators will show continuity for the center conductor and the shield.
Testing USB Cables
- Connect one end of the USB cable (Type A or B, depending on the tester's ports) to the main unit.
- Connect the other end to the remote unit.
- පරීක්ෂකය සක්රිය කරන්න.
- The LEDs will indicate continuity for the power, data+, data-, and ground lines of the USB cable.
නඩත්තු කිරීම
පිරිසිදු කිරීම
Wipe the device with a soft, dry, lint-free cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the casing හෝ අභ්යන්තර සංරචක.
ගබඩා කිරීම
Store the device in a cool, dry place, away from direct sunlight and extreme temperatures. If the device will not be used for an extended period, remove the battery to prevent potential leakage and damage.
දෝෂගවේෂණය
උපාංගය බලගන්වන්නේ නැත.
- Check if the 9V battery is correctly installed with the proper polarity.
- Ensure the battery has sufficient charge. Replace with a new 9V battery if necessary.
- Verify the power switch is firmly in the "ON" position.
LEDs do not light up or show inconsistent patterns.
- Ensure all cables are securely connected to both the main and remote units. Loose connections can cause false readings.
- Inspect the cable being tested for visible damage, kinks, or frayed connectors.
- Test with a known good cable to verify the tester's functionality. If the known good cable tests correctly, the issue lies with the original cable.
- Replace the battery if the LEDs appear dim, flicker, or behave erratically, indicating low power.
පිරිවිතර
- ආකෘතිය: Delock 86108
- සහාය දක්වන සම්බන්ධක: BNC, RJ-12, RJ-45, USB
- සංදර්ශක වර්ගය: LED දර්ශක
- බලශක්ති ප්රභවය: 1 x 9V බැටරි (ඇතුළත් නොවේ)
- මානයන් (L x W x H): 185 mm x 80 mm x 32 mm (7.28 x 3.15 in x 1.26 in)
- බර: ග්රෑම් 470 (අවුන්ස 16.58)
- නිෂ්පාදන වර්ණය: රතු, කහ
වගකීම් සහ සහාය
For detailed warranty information, technical support, or service inquiries, please refer to the documentation provided with your original purchase or contact your authorized retailer. Please retain your proof of purchase for any warranty claims.
