1. හැඳින්වීම
This manual provides essential instructions for the safe operation, assembly, maintenance, and troubleshooting of your HECHT 135 BTS 2-stroke petrol brush cutter. Please read this manual thoroughly before using the equipment to ensure safe and efficient operation.
2. ආරක්ෂිත උපදෙස්
Operating a petrol brush cutter requires strict adherence to safety guidelines to prevent injury. Always prioritize your safety and the safety of others.
2.1 පුද්ගලික ආරක්ෂක උපකරණ (PPE)
- අක්ෂි ආරක්ෂාව: Always wear safety glasses or a face shield to protect against flying debris.
- ශ්රවණ ආරක්ෂණය: Use earplugs or earmuffs to prevent hearing damage from engine noise.
- අත් ආරක්ෂාව: Wear sturdy work gloves to improve grip and protect hands.
- පාද ආරක්ෂාව: Wear non-slip, steel-toed boots or sturdy footwear.
- ශරීර ආරක්ෂණය: Wear long pants and a long-sleeved shirt to protect skin from debris and sun. Avoid loose clothing that could get caught in moving parts.
2.2 සාමාන්ය ආරක්ෂණ පූර්වාරක්ෂාවන්
- අත්පොත කියවන්න: ක්රියාත්මක වීමට පෙර සියලුම උපදෙස් සහ අනතුරු ඇඟවීම් තේරුම් ගන්න.
- Area Inspection: Before starting, clear the work area of stones, metal objects, wires, and other debris that could be thrown or entangle the cutting head.
- නරඹන්නන්: සියලුම නරඹන්නන්, ළමයින් සහ සුරතල් සතුන් මෙහෙයුම් ප්රදේශයෙන් ආරක්ෂිත දුරකින් (අවම වශයෙන් මීටර් 15 ක්) තබා ගන්න.
- ඉන්ධන හැසිරවීම: Handle petrol with extreme care. Refuel in a well-ventilated area with the engine off and cool. Do not smoke while refueling.
- ස්ථාවර පාදම: Maintain firm footing and balance at all times. Do not overreach.
- කාලගුණික තත්ත්වයන්: Do not operate in rain or wet conditions, or when visibility is poor.
- තෙහෙට්ටුව: Do not operate the brush cutter when tired, ill, or under the influence of alcohol or drugs.
- නඩත්තු: Always turn off the engine and disconnect the spark plug before performing any maintenance, cleaning, or clearing blockages.
- ප්රවාහන: Transport the brush cutter with the engine off and the cutting attachment protected.
3. පැකේජ අන්තර්ගතය
Upon unpacking your HECHT 135 BTS brush cutter, verify that all components are present and undamaged:
- 1x HECHT 135 BTS Petrol Brush Cutter unit
- 1x 3-tooth Metal Blade (255 mm cutting width)
- 1x Dual-line Spool Head (430 mm cutting width)
- 1x සකස් කළ හැකි උරහිස් පටිය
- 1x Handlebar assembly
- 1x Cutting Guard
- 1x Tool Kit (for assembly and basic maintenance)
- 1x පරිශීලක අත්පොත
4. සැකසීම සහ එකලස් කිරීම
Follow these steps to assemble your brush cutter before first use.
4.1 හැන්ඩ්ල්බාර් ඇමිණීම
- හසුරුව cl ලිහිල් කරන්නamp bolts on the main shaft.
- Position the handlebar onto the shaft at a comfortable working height and angle.
- Ensure all control cables are routed correctly and not pinched.
- cl එක තද කරන්නamp බෝල්ට් ආරක්ෂිතව සවි කරන්න.
4.2 Installing the Cutting Guard
- Slide the cutting guard onto the lower shaft, ensuring it is oriented correctly to protect against debris.
- Secure the guard with the provided screws or bolts. Do not operate the brush cutter without the guard properly installed.
4.3 Mounting the Cutting Head
Your HECHT 135 BTS comes with two interchangeable cutting heads: a 3-tooth metal blade and a dual-line spool head.
- Ensure the engine is off and the spark plug cap is removed.
- Insert the locking pin into the gearbox hole to prevent the shaft from rotating.
- For Metal Blade: Place the blade onto the shaft, ensuring it sits correctly on the support flange. Secure it with the washer and nut, tightening firmly (often left-hand thread).
- For Spool Head: Thread the spool head onto the shaft, turning clockwise until it is securely fastened.
- අගුලු දැමීමේ පින් එක ඉවත් කරන්න.
4.4 උරහිස් පටිය ඇමිණීම
- Attach the shoulder strap to the designated hook or loop on the main shaft.
- Adjust the strap length so the cutting head is balanced and comfortable for your working posture, allowing for a slight bend in your arms.
4.5 Fueling the Brush Cutter
The HECHT 135 BTS uses a 2-stroke engine, requiring a specific petrol-oil mixture. Refer to the engine manufacturer's recommendations for the correct mixing ratio (typically 25:1 or 50:1, depending on the oil type).
- Use fresh, unleaded petrol and high-quality 2-stroke engine oil.
- වෙනම අනුමත ඉන්ධන භාජනයක ඉන්ධන මිශ්ර කරන්න.
- Ensure the engine is off and cool before refueling.
- Carefully pour the mixed fuel into the fuel tank (capacity 0.7 L), avoiding spills.
- ඉන්ධන පියන ආරක්ෂිතව වසා දමන්න.
5. මෙහෙයුම් උපදෙස්
5.1 එන්ජිම ආරම්භ කිරීම
- බුරුසු කපනය පැතලි, ස්ථාවර මතුපිටක් මත තබන්න.
- ON/OFF ස්විචය 'ON' ස්ථානයට සකසන්න.
- Engage the choke (if the engine is cold).
- ඉන්ධන පෙනෙන තුරු ප්රයිමර් බල්බය කිහිප වතාවක් ඔබන්න.
- Hold the brush cutter firmly with one hand on the handlebar and the other on the starter grip.
- Pull the starter cord slowly until resistance is felt, then pull sharply and quickly until the engine fires (usually 1-3 pulls).
- Once the engine fires, disengage the choke (if applicable).
- සම්පූර්ණ තෙරපුම යෙදීමට පෙර එන්ජිම මිනිත්තු කිහිපයක් උණුසුම් වීමට ඉඩ දෙන්න.
5.2 Using the Brush Cutter
Hold the brush cutter firmly with both hands on the handlebar. Maintain a wide stance for balance. The shoulder strap should support the weight of the machine, allowing you to guide it with minimal effort.
- කැපීමේ තාක්ෂණය: Use a sweeping motion from side to side. For dense growth, cut in smaller sections.
- Blade Use: Ideal for thick weeds, brush, and small saplings. Be aware of kickback when using the blade.
- Spool Head Use: Best for grass, light weeds, and trimming around obstacles. Advance the line as needed by tapping the head on the ground (tap-and-go system) or manually.
- Maintain RPM: Operate at a consistent, high RPM for efficient cutting and to prevent engine strain.
- බාධක වළක්වා ගන්න: Do not strike hard objects like rocks, fences, or concrete with the cutting head.
5.3 එන්ජිම නැවැත්වීම
- Release the throttle to allow the engine to idle.
- Move the ON/OFF switch to the 'OFF' position.
- Wait for all moving parts to come to a complete stop before setting the machine down.
6. නඩත්තු කිරීම
Regular maintenance ensures the longevity and safe operation of your HECHT 135 BTS brush cutter.
6.1 එක් එක් භාවිතයෙන් පසු
- ඒකකය පිරිසිදු කරන්න: Remove grass, dirt, and debris from the engine, cutting head, and guard. Use a brush or compressed air.
- Inspect Cutting Head: Check the blade for sharpness and damage, or the line spool for wear and proper function. Replace or sharpen as needed.
- ගාංචු පරීක්ෂා කරන්න: Ensure all nuts, bolts, and screws are tight.
6.2 කාලානුරූප නඩත්තු කිරීම
- වායු පෙරහන: Clean the air filter regularly (every 5-10 hours of operation, more often in dusty conditions). Wash foam filters in warm, soapy water, rinse, dry, and lightly oil. Replace paper filters if heavily soiled.
- පුලිඟු පේනුව: Inspect the spark plug every 20-30 hours. Clean carbon deposits and adjust the gap if necessary. Replace if electrodes are worn or damaged.
- ඉන්ධන පෙරහන: Inspect and replace the fuel filter in the tank annually or if fuel flow issues occur.
- ගියර් පෙට්ටිය ලිහිසි කිරීම: Check and replenish the grease in the gearbox (at the cutting head end) as per manufacturer recommendations, typically every 25-50 hours.
- සිසිලන වරල්: අධික උනුසුම් වීම වැළැක්වීම සඳහා එන්ජිමේ සිසිලන වරල් පිරිසිදුව තබා ගන්න.
6.3 ගබඩා කිරීම
- For long-term storage, drain the fuel tank and run the engine until it stops to clear the carburetor of fuel.
- මුළු ඒකකයම හොඳින් පිරිසිදු කරන්න.
- Store in a dry, well-ventilated area, away from direct sunlight and heat sources.
7. දෝශ නිරාකරණය
මෙම කොටස ඔබේ බුරුසු කටර් සමඟ ඔබට මුහුණ දීමට සිදුවිය හැකි පොදු ගැටළු ආමන්ත්රණය කරයි.
| ගැටලුව | විය හැකි හේතුව | විසඳුම |
|---|---|---|
| එන්ජිම පණ ගැන්වෙන්නේ නැහැ | No fuel, incorrect choke, fouled spark plug, clogged fuel filter, old fuel. | Check fuel level and mixture. Adjust choke. Clean/replace spark plug. Clean/replace fuel filter. Use fresh fuel. |
| මෙහෙයුම අතරතුර බලය අහිමි වීම | Clogged air filter, incorrect fuel mixture, dull cutting head, engine overheating. | Clean air filter. Verify fuel mixture. Sharpen/replace cutting head. Clean cooling fins. |
| අධික කම්පනය | Damaged or unbalanced cutting head, loose fasteners, bent shaft. | Inspect and replace damaged cutting head. Tighten all fasteners. If shaft is bent, seek professional service. |
| කැපුම් රේඛාව ඉදිරියට නොයයි | Line tangled, insufficient line, incorrect spool installation. | Turn off engine, clear tangles, reload line, ensure spool is correctly installed. |
8. පිරිවිතර
Technical data for the HECHT 135 BTS Petrol Brush Cutter:
- එන්ජින් වර්ගය: 2-පහර, තනි සිලින්ඩරය
- විස්ථාපනය: 33 cm³
- ශ්රේණිගත බලය: 0.9 kW / 1.2 HP
- Max. Engine Power: 1.1 kW / 1.5 HP
- ශ්රේණිගත එන්ජින් වේගය: 6500 rpm
- උපරිම. එන්ජින් වේගය: 13000 rpm
- ඉන්ධන ටැංකි පරිමාව: 0.7 L
- Blade Cutting Width: 255 මි.මී. (25.5 සෙ.මී.)
- Line Cutting Width: 430 මි.මී. (43 සෙ.මී.)
- Max. Line Thickness: 2.5 මි.මී
- Max. Spool Head Speed: 8500 rpm
- ශුද්ධ බර: කිලෝ ග්රෑම් 6.1 කි
- මුළු දිග: 1880 මි.මී
- මුළු පළල: 720 මි.මී
- මුළු උස: 400 මි.මී
9. නිෂ්පාදන රූප
Visual references for the HECHT 135 BTS Brush Cutter.
රූප විස්තරය: This is a placeholder image indicating 'No image available'. A typical product image would show the HECHT 135 BTS 2-stroke petrol brush cutter fully assembled, highlighting its handlebar, engine unit, and interchangeable cutting heads (3-tooth blade and line spool).
10. වගකීම් සහ සහාය
For warranty claims, technical support, or spare parts inquiries, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty validation.
සටහන: මෙම නිෂ්පාදනය සඳහා අමතර කොටස් තිබේද යන්න පිළිබඳ තොරතුරු දැනට නොමැත.
