හැඳින්වීම
This instruction manual provides essential information for the safe and proper installation, operation, and maintenance of your Eaton CH 1P 20A Ground Fault Circuit Interrupter (GFCI) with Pigtail. Please read this manual thoroughly before installation and keep it for future reference. This device is designed to protect against electrical shock hazards in residential and commercial applications.
ආරක්ෂිත තොරතුරු
අවවාදයයි: විදුලි සැර වැදීමේ හෝ ගින්නක් ඇතිවීමේ අවදානම.
- සියලුම ජාතික සහ දේශීය විදුලි කේතයන්ට අනුකූලව සුදුසුකම් ලත් විදුලි කාර්මිකයෙකු විසින් ස්ථාපනය සිදු කළ යුතුය.
- Turn off power at the main service panel before installing or servicing this device. Failure to do so can result in serious injury or death.
- මෙම උපකරණය හානි වී ඇති බව පෙනේ නම් එය භාවිතා නොකරන්න.
- නිසි බිම් සැකසීම සහතික කරන්න.
- Test the GFCI regularly as described in the Operating Instructions section.
නිෂ්පාදනය අවසන්view
The Eaton CH 1P 20A GFCI with Pigtail is a single-pole, 20-amp circuit breaker designed to provide ground fault protection. It features a pigtail neutral wire for easy connection to the neutral bus bar in your load center. This device is compatible with Eaton CH series load centers.
රූපය 1: Eaton CH 1P 20A GFCI Circuit Breaker. This image shows the compact design of the single-pole, 20-amp GFCI breaker, including its distinctive test and reset buttons and the attached pigtail neutral wire for installation.
සැකසුම සහ ස්ථාපනය
ඔබ ආරම්භ කිරීමට පෙර: Ensure the main power to the electrical panel is OFF. Use a voltagබලය අක්රිය බව තහවුරු කිරීමට ඊ පරීක්ෂකය.
- පැනලය සකස් කරන්න: Open the electrical panel cover. Locate an available space for a single-pole breaker.
- Connect the Pigtail: Connect the white (neutral) pigtail wire from the GFCI breaker to the neutral bus bar in the panel. Ensure a secure connection.
- Connect the Load Wire: Connect the black (hot) load wire from the circuit you are protecting to the terminal on the GFCI breaker. Tighten the screw securely.
- බ්රේකරය ස්ථාපනය කරන්න: Snap the GFCI breaker firmly onto the hot bus bar in the panel. Ensure it is fully seated.
- Connect the Neutral Load Wire: Connect the white (neutral) load wire from the circuit you are protecting to the designated neutral terminal on the GFCI breaker. Do not connect this neutral wire to the panel's neutral bus bar.
- බලය ප්රතිස්ථාපනය කරන්න: Close the electrical panel cover. Turn the main power back ON.
- GFCI පරීක්ෂා කරන්න: Perform the operational test as described in the "Operating Instructions" section.
මෙහෙයුම් උපදෙස්
Regular testing of the GFCI circuit breaker is crucial to ensure it is functioning correctly and providing continuous protection against ground faults. Test monthly or after any electrical storm.
- පරීක්ෂණය: With power ON, press the "TEST" button on the face of the GFCI breaker. The breaker should immediately trip to the OFF position.
- නැවත සකසන්න: To restore power, push the breaker handle firmly to the "OFF" position, then push it to the "ON" position.
- සත්යාපනය: If the GFCI does not trip when the "TEST" button is pressed, or if it does not reset, it may be faulty or improperly wired. Discontinue use and consult a qualified electrician.
නඩත්තු කිරීම
The Eaton GFCI circuit breaker requires minimal maintenance. Perform the monthly test as described in the Operating Instructions. Keep the area around the electrical panel clean and free of obstructions. Do not attempt to repair a faulty GFCI; replace it with a new one.
දෝෂගවේෂණය
| ගැටලුව | විය හැකි හේතුව | විසඳුම |
|---|---|---|
| GFCI නිතර සංචාරය කරයි. | Ground fault in the circuit; faulty appliance; moisture. | Unplug all appliances on the circuit and reset. If it holds, plug in appliances one by one to identify the faulty one. Check for moisture in outlets or wiring. If problem persists, consult an electrician. |
| GFCI does not trip when TEST button is pressed. | Faulty GFCI; incorrect wiring. | Ensure power is on. If it still doesn't trip, the GFCI is faulty and needs replacement. Verify wiring connections. |
| GFCI does not reset. | Persistent ground fault; faulty GFCI. | Ensure the breaker handle is pushed fully to OFF before attempting to reset to ON. If a ground fault is present, it will not reset. Address the ground fault or replace the GFCI if it's faulty. |
පිරිවිතර
| විශේෂාංගය | විස්තර |
|---|---|
| වෙළඳ නාමය | ඊටන් |
| මාදිලියේ නම | CH 1P 20A GFCI W/PIGTAIL |
| කොටස අංකය | CHFN120GF |
| වත්මන් ශ්රේණිගත කිරීම | 20 Amps |
| වෙළුමtage | වෝල්ට් 120 |
| ධ්රැව සංඛ්යාව | 1 |
| පරිපථ කඩන වර්ගය | ජීඑෆ්සීඅයි |
| සවිකිරීමේ වර්ගය | ප්ලග්-ඉන් මවුන්ට් |
| අයිතම මානයන් (LxWxH) | අඟල් 7 x 4 x 2 |
| ද්රව්ය | ප්ලාස්ටික් |
| UPC | 786689058876 |
වගකීම් තොරතුරු
This Eaton product comes with a manufacturer's warranty. For specific details regarding warranty coverage, duration, and claims process, please refer to the warranty documentation included with your purchase or visit the official Eaton webවෙබ් අඩවිය. වගකීම් අරමුණු සඳහා ඔබේ මිලදී ගැනීමේ සාක්ෂි තබා ගන්න.
පාරිභෝගික සහාය
If you have any questions, require technical assistance, or need to report an issue with your Eaton CH 1P 20A GFCI, please contact Eaton customer support. You can find contact information on the official Eaton webවෙබ් අඩවියෙන් හෝ ඔබේ නිෂ්පාදනය සමඟ සපයා ඇති ලියකියවිලි හරහා.
ඊටන් නිල Webඅඩවිය: www.eaton.com
