Lepro LE අඩි 50 RGB 5050 LED තීරු ලයිට් උපදෙස් අත්පොත

හැඳින්වීම

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Lepro LE 50ft RGB 5050 LED Strip Lights. Please read this manual thoroughly before installation and use to ensure proper function and safety. Keep this manual for future reference.

ආරක්ෂිත උපදෙස්

• ස්ථාපනය කිරීමට හෝ නඩත්තු කිරීමට පෙර බල සැපයුම විසන්ධි කර ඇති බවට සහතික වන්න.
• This product is designed for indoor use only. Avoid exposure to water or high humidity.
• Do not connect the LED strip to the power supply while it is still coiled on the reel. Unroll the strip completely before powering on to prevent overheating.
• Use only the provided 12V ETL-listed power adapter. Using an incompatible power supply may damage the product and void the warranty.
• Do not bend the LED strip at sharp angles (less than 90 degrees) to avoid damaging the circuit board or LEDs.
• දරුවන්ට ළඟා විය නොහැකි ලෙස තබා ගන්න.
• If any damage is observed on the strip or power adapter, discontinue use immediately and contact customer support.

පැකේජයේ අන්තර්ගතය

Image: The complete package contents including two rolls of LED strip lights, a remote control, a power adapter, and fixing clips with screws.

පහත ලැයිස්තුගත කර ඇති සියලුම අයිතම ඔබේ පැකේජයට ඇතුළත් කර ඇති බව කරුණාකර සත්‍යාපනය කරන්න:

• 2 x 24.6ft (total 50ft) RGB 5050 LED Strip Lights
• 1 x IR Remote Controller (44-key)
• 1 x 12V ETL-listed Power Adapter
• 1 x පාලන පෙට්ටිය
• සවි කිරීම් ක්ලිප් සහ ඉස්කුරුප්පු
• පරිශීලක අත්පොත (මෙම ලේඛනය)

පිරිවිතර

පිහිටුවීම සහ ස්ථාපනය

Follow these steps for proper installation of your LED strip lights:

1. මතුපිට සකස් කරන්න:

   Before attaching the LED strip, ensure the installation surface is clean, dry, and smooth. Wipe the surface with a clean cloth to remove dust or debris. This ensures optimal adhesion of the 3M adhesive backing.

   

   Image: A hand wiping a wooden surface with a cloth, illustrating the first step of surface preparation.

2. සංරචක සම්බන්ධ කරන්න:

   Connect the 4-pin connector from the LED strip to the control box. Ensure the arrow mark on the strip's connector aligns with the arrow mark on the control box. Then, connect the DC wire from the power adapter to the control box. Finally, plug the power adapter into a standard electrical outlet.

   

   Image: A visual guide demonstrating how to connect the DC wire to the control box and the 4-pin connector to the LED strip, emphasizing arrow alignment.

   වැදගත්: Ensure the "arrow" mark on the LED strip connector and the "12V" mark on the control box are on the same side for correct polarity.

   

   Image: Detail of the RGB light strip, highlighting the 10mm 4-pin connector and the strong 3M self-adhesive backing for installation.

3. LED තීරුව අමුණන්න:

   Peel off the protective backing from the 3M adhesive on the back of the LED strip. Carefully press the strip onto the prepared surface, applying firm and even pressure along its entire length. For added security, use the included fixing clips and screws at regular intervals, especially around corners or areas with less adhesion.

   

   Image: A hand demonstrating how to peel and attach the LED strip to a surface, showing the adhesive backing.

4. දුරස්ථ පාලක සූදානම:

   Before using the remote control, pull out the transparent plastic chip from the battery compartment. This activates the battery.

   

   Image: A close-up showing a hand pulling the transparent plastic chip from the remote control, indicating battery activation.

ස්ථාපන නිදර්ශන වීඩියෝව

මෙහෙයුම

Your LED strip lights are controlled by the included 44-key IR remote control. Point the remote directly at the IR receiver on the control box for optimal response.

රූපය: සවිස්තරාත්මක view of the 44-key remote control, showing buttons for power, brightness adjustment, RGB color selection, 6 DIY color buttons, and various dynamic modes like Jump, Fade, Quick, Slow, and Auto.

• බලය සක්රිය / අක්රිය: ඔබන්න රතු බල බොත්තම විදුලි පහන් සක්‍රිය හෝ අක්‍රිය කිරීමට.
• දීප්තිය ගැලපීම: භාවිතා කරන්න ඉහළ සහ පහළ ඊතල බොත්තම් (above the R, G, B, W buttons) to increase or decrease brightness.
• වර්ණ තේරීම: ඕනෑම එකක් ඔබන්න 20 color buttons to select a static color.
• DIY වර්ණ:
  1. එකක් ඔබන්න DIY1-DIY6 buttons.
  2. භාවිතා කරන්න RGB up/down arrows to adjust the intensity of Red, Green, and Blue to create your desired custom color.
  3. Press the same DIY button again to save the custom color.
• ගතික මාදිලි:
  • JUMP3 / JUMP7: Cycles through 3 or 7 colors with a jump effect.
  • FADE3 / FADE7: Fades between 3 or 7 colors.
  • ඉක්මන් / මන්දගාමී: Adjusts the speed of dynamic modes.
  • ස්වයංක්‍රීය: Cycles through all available dynamic modes.
  • සැණෙළිය: Flashes through colors.

නඩත්තු කිරීම

• පිරිසිදු කිරීම: Ensure the power is off and unplugged before cleaning. Gently wipe the LED strip with a dry, soft cloth. Do not use liquid cleaners or abrasive materials.
• ගබඩා: If storing the lights for an extended period, ensure they are clean and dry. Store in a cool, dry place away from direct sunlight.
• ඇලවීම: If the adhesive begins to lose its stickiness, you can reinforce the strip with additional fixing clips or a suitable adhesive tape (not included).

දෝෂගවේෂණය

වගකීම් සහ සහාය

Lepro products are designed for quality and reliability. For warranty information, technical support, or any questions regarding your LED strip lights, please contact Lepro customer service through the retailer where the product was purchased or visit the official Lepro webඅඩවිය.

Please have your model number (410105-RGB-US) and purchase details ready when contacting support.