Morris 90308 Hex Head Split Bolts 3/0 Instruction Manual

1. නිෂ්පාදන අවසන්view

The Morris 90308 Hex Head Split Bolt 3/0 is designed for making secure electrical connections between copper conductors. Manufactured from high-strength, high-conductivity electrolytic copper alloy, this connector ensures maximum strength and conductivity. It is rated for copper conductors only and is reusable. This product is suitable for 600V applications and temperatures up to 194°F (90°C). It is UL486, UL486A-486B, and CSA C22.2 No. 65-13 listed, including for direct burial and grounding/bonding applications.

Image 1.1: Morris 90308 Hex Head Split Bolt 3/0. This image shows the copper alloy split bolt with a hex head for tightening electrical connections.

2 ආරක්ෂිත තොරතුරු

Always observe standard electrical safety precautions when working with electrical components. Failure to do so may result in serious injury or property damage.

• ස්ථාපනය හෝ නඩත්තු කිරීමට පෙර විදුලිය විසන්ධි කර ඇති බවට සහතික වන්න.
• පරිවරණය කළ අත්වැසුම් සහ ආරක්ෂිත කණ්නාඩි ඇතුළු සුදුසු පුද්ගලික ආරක්ෂක උපකරණ (PPE) පළඳින්න.
• Only use this product with copper conductors. Do not use with aluminum conductors.
• Ensure connections are made by qualified personnel in accordance with local electrical codes and regulations.
• ශ්‍රේණිගත කළ පරිමාව ඉක්මවා නොයන්නtage (600V) or temperature (194°F / 90°C).

3. පිහිටුවීම සහ ස්ථාපනය

Follow these steps for proper installation of the Morris 90308 Hex Head Split Bolt:

1. Prepare Conductors: Strip the insulation from the ends of the copper conductors to be joined, ensuring enough bare wire to fit securely within the bolt's channels. Clean the conductors if necessary to remove any oxidation or debris.
2. Insert Conductors: Loosen the hex head bolt sufficiently to allow the conductors to be inserted into the split bolt's channels. Insert one conductor into each side of the split bolt.
3. Tighten Connection: Using an appropriate wrench, tighten the hex head bolt. Apply firm and even pressure to ensure a secure mechanical and electrical connection. The split bolt design is intended to compress around the conductors.
4. සම්බන්ධතාවය තහවුරු කරන්න: After tightening, gently tug on the conductors to ensure they are firmly held and cannot be easily pulled out. The connection should be tight and stable.
5. Insulate (if necessary): For applications requiring insulation, wrap the completed connection with appropriate electrical tape or heat shrink tubing, ensuring full coverage and protection from environmental factors.

This split bolt is reusable; however, inspect it for any damage or wear before reuse to ensure continued performance and safety.

4. මෙහෙයුම් උපදෙස්

Once properly installed, the Morris 90308 Hex Head Split Bolt functions as a permanent electrical connector. No further operational steps are required beyond ensuring the initial secure installation. The bolt maintains the electrical continuity between the joined copper conductors.

5. නඩත්තු කිරීම

Periodic inspection of electrical connections is recommended to ensure long-term reliability and safety.

• දෘශ්‍ය පරීක්ෂාව: Regularly check the split bolt and surrounding conductors for any signs of corrosion, overheating (discoloration), or physical damage.
• තද බව පරීක්ෂා කිරීම: If accessible and safe to do so (with power disconnected), periodically check the tightness of the hex head bolt to ensure the connection remains secure.
• පිරිසිදු කිරීම: If dirt or debris accumulates, clean the exterior of the connection with a dry, non-conductive cloth.

6. දෝශ නිරාකරණය

If an electrical issue is suspected at a connection point, consider the following:

• Loss of Continuity: If there is a loss of electrical continuity, ensure the hex head bolt is sufficiently tightened. A loose connection can lead to increased resistance and potential failure.
• අධික උනුසුම් වීම / දුර්වර්ණ වීම: Signs of overheating (e.g., melted insulation, discolored bolt) indicate a poor connection or an overloaded circuit. Immediately disconnect power and inspect the connection. Re-tighten or replace the bolt if necessary, and verify the circuit load.
• විඛාදනය: In outdoor or damp environments, corrosion can occur. Ensure proper insulation and environmental protection. If corrosion is severe, replace the bolt.

Always ensure power is off before attempting any troubleshooting or repairs.

7. පිරිවිතර

8. වගකීම් සහ සහාය

For warranty information and technical support regarding the Morris 90308 Hex Head Split Bolt 3/0, please refer to the official Morris Products webවෙබ් අඩවියට හෝ ඔවුන්ගේ පාරිභෝගික සේවා දෙපාර්තමේන්තුවට කෙලින්ම සම්බන්ධ වන්න. ඕනෑම වගකීම් හිමිකම් සඳහා ඔබේ මිලදී ගැනීමේ රිසිට්පත තබා ගන්න.