AeroCool Blade ATX Semi-Tower PC Case Instruction Manual

1. හැඳින්වීම

The AeroCool Blade is an ATX semi-tower PC case designed for optimal airflow and aesthetic appeal. It features an RGB front panel with preset lighting modes, a full tempered glass side window, and ample space for component installation. This manual provides essential information for the proper setup, operation, and maintenance of your PC case.

ආරක්ෂිත තොරතුරු: Always disconnect power from your system before performing any installation or maintenance. Handle components with care to avoid damage. Refer to individual component manuals for specific installation instructions.

2. පැකේජ අන්තර්ගතය

• AeroCool Blade ATX Semi-Tower PC Case
• 1 x 120mm RGB Rear Fan (pre-installed)
• 3 x 120mm Front Fans (pre-installed)
• උපාංග කට්ටලය (ඉස්කුරුප්පු, ස්ථාවරයන්, කේබල් බැඳීම්)

3. පිහිටුවීම සහ ස්ථාපනය

3.1 නඩුව සකස් කිරීම

Carefully remove the case from its packaging. Place it on a stable, flat surface. Remove the tempered glass side panel by unscrewing the thumb screws at the rear of the case and gently pulling the panel away.

රූපය 3.1: අභ්යන්තර view of the AeroCool Blade PC case, illustrating the layout for component installation.

3.2 මවු පුවරුව සවි කිරීම

1. Install the necessary motherboard standoffs into the motherboard tray according to your motherboard's form factor (ATX, Micro-ATX, Mini-ITX).
2. නඩුවේ පසුපස විවරයට I/O පලිහ සවි කරන්න.
3. ඔබේ මවු පුවරුව ස්ටෑන්ඩ්ඕෆ් මත ප්‍රවේශමෙන් තබන්න, ඉස්කුරුප්පු සිදුරු පෙළගස්වන්න.
4. සපයා ඇති ඉස්කුරුප්පු වලින් මවු පුවරුව සුරක්ෂිත කරන්න.

3.3 බල සැපයුම් ඒකකය (PSU) ස්ථාපනය

The AeroCool Blade supports bottom-mounted PSUs. Slide your PSU into the dedicated compartment at the bottom rear of the case. Secure it with screws from the rear of the case.

3.4 ගබඩා ධාවක ස්ථාපනය

• 3.5" HDD තැටි: Install 3.5" hard drives into the drive cage located beneath the PSU shroud.
• 2.5" SSDs/HDDs: Install 2.5" drives onto the dedicated mounting points on the motherboard tray or behind it.

Figure 3.2: Rear internal view, highlighting cable management routes and 2.5-inch drive mounting locations.

3.5 Expansion Card (GPU) Installation

Remove the necessary expansion slot covers from the rear of the case. Insert your graphics card or other expansion cards into the PCIe slots on your motherboard and secure them with screws.

3.6 විදුලි පංකා සහ සිසිලන ස්ථාපනය

The case comes with one 120mm RGB fan pre-installed at the rear and three 120mm fans pre-installed at the front. Ensure all fan cables are connected to appropriate headers on your motherboard or fan controller.

Figure 3.3: A 120mm RGB fan, similar to those pre-installed in the AeroCool Blade case.

3.7 Front Panel I/O Connections

Connect the front panel cables (USB 3.0, USB 2.0, HD Audio, Power Switch, Reset Switch, LED Switch, Power LED, HDD LED) to the corresponding headers on your motherboard. Refer to your motherboard manual for exact pin configurations.

4. මෙහෙයුම් උපදෙස්

4.1 බල ගැන්වීම

Once all components are installed and connected, replace the side panel. Connect your monitor, keyboard, mouse, and power cable to the PSU. Press the Power button located on the top panel of the case to turn on your system.

රූපය 4.1: ඉහළ-ඉදිරිපස view of the case, indicating the location of the power button and front I/O ports.

4.2 RGB ආලෝකකරණ පාලනය

The AeroCool Blade features an RGB front panel. Use the dedicated LED button on the top panel to cycle through various preset lighting modes and effects. Pressing the button will change the lighting pattern or color.

රූපය 4.2: ඉදිරිපස view of the AeroCool Blade case with its distinctive RGB lighting.

4.3 ඉදිරිපස පැනල් තොටුපළවල්

ඉහළ පුවරුව පහසු ප්‍රවේශයක් සපයයි:

• 1 x USB 3.0 port
• 2 x USB 2.0 ports
• HD Audio output
• මයික්රොෆෝන ආදානය

Connect your USB devices, headphones, and microphone to these ports as needed.

5. නඩත්තු කිරීම

5.1 දූවිලි පෙරහන් පිරිසිදු කිරීම

Regularly check and clean the dust filters to maintain optimal airflow and prevent dust buildup inside the case. Dust filters are typically located at the top, front, and bottom (under the PSU). Gently remove them and clean with compressed air or rinse with water (ensure they are completely dry before re-installation).

5.2 බාහිර පිරිසිදු කිරීම

Wipe the exterior surfaces of the case with a soft, damp cloth. Avoid using harsh chemicals or abrasive materials that could damage the finish or tempered glass.

6. දෝශ නිරාකරණය

• පද්ධතිය ක්‍රියාත්මක නොවේ:
  Ensure the PSU is switched on and properly connected to the wall outlet. Verify all power cables from the PSU are correctly connected to the motherboard and components. Check the front panel power switch connection to the motherboard.
• RGB ආලෝකය ක්‍රියා නොකරයි:
  Ensure the RGB controller (if applicable) and fan RGB cables are securely connected. Press the LED button on the top panel to cycle through modes. If connected to a motherboard header, check motherboard software settings.
• කැරකෙන්නේ නැති විදුලි පංකා:
  Verify that all fan power cables are securely connected to the motherboard fan headers or a fan controller. Check BIOS/UEFI settings for fan speed control.
• Front Panel USB/Audio Not Working:
  Ensure the USB and HD Audio cables from the front panel are correctly connected to the corresponding headers on your motherboard.

7. පිරිවිතර

Figure 7.1: Dimensions of the AeroCool Blade PC Case.

8. වගකීම් සහ සහාය

For warranty information and technical support, please refer to the official AeroCool webවෙබ් අඩවියට පිවිසෙන්න හෝ ඔබේ ප්‍රදේශයේ සිල්ලර වෙළෙන්දා අමතන්න. වගකීම් හිමිකම් සඳහා ඔබේ මිලදී ගැනීමේ සාක්ෂි තබා ගන්න.

සබඳතා තොරතුරු: වැඩිදුර සහාය සඳහා, කරුණාකර පිවිසෙන්න www.aerocool.io.