TORNADO TEEE-30DS Electric Water Heater User Manual

හැඳින්වීම

Thank you for choosing the TORNADO TEEE-30DS Electric Water Heater. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new water heater. Please read these instructions thoroughly before installation and use, and retain them for future reference.

වැදගත් ආරක්ෂක උපදෙස්

Failure to follow these safety instructions could result in property damage, serious injury, or death. Always consult a qualified professional for installation and repairs.

• විදුලි ආරක්ෂාව: Ensure the water heater is connected to a properly grounded electrical outlet with the correct voltage (1500 watts). Do not use extension cords. Disconnect power before any maintenance or service.
• ජල පීඩනය: The maximum operating pressure is 8 bars. Do not exceed this pressure. Install a pressure relief valve if local codes require it.
• උෂ්ණත්ව සැකසුම්: Hot water can cause severe burns. Set the thermostat to a safe temperature to prevent scalding, especially in households with children or elderly individuals.
• ස්ථාපනය: Installation must be performed by a qualified technician in accordance with all local codes and regulations. Ensure proper ventilation and drainage.
• නඩත්තු: Regular maintenance is crucial for safe and efficient operation. Do not attempt repairs beyond the scope of this manual. Contact authorized service personnel.

නිෂ්පාදනය අවසන්view

The TORNADO TEEE-30DS is a 30-liter electric water heater designed for indoor installation. It features an enamel-coated inner tank for corrosion resistance and an LED lamp indicator for operational status.

රූපය 1: ඉදිරිපස view of the TORNADO TEEE-30DS Electric Water Heater. This image shows the compact design suitable for indoor installation, with the control panel and LED indicator visible.

ප්රධාන සංරචක:

• අභ්‍යන්තර ටැංකිය: 30-liter capacity, enamel-coated for durability and corrosion resistance.
• තාපන මූලද්රව්යය: 1500-watt electric heating element.
• තාප ස්ථාය: Controls water temperature.
• LED එල්amp: Indicates heating status.
• Temperature/Pressure Relief Valve (TPR Valve): Safety device (Note: May be supplied separately or integrated, check local codes).
• ඇතුල්වීමේ/පිටවන නල: Connections for cold water supply and hot water output.

සැකසුම සහ ස්ථාපනය

Installation should only be performed by a qualified professional. Ensure all local plumbing and electrical codes are met.

1. ස්ථානයක් තෝරා ගැනීම:

• Install indoors, in a dry area, protected from freezing temperatures.
• Ensure the wall or mounting surface can support the full weight of the water heater (approximately 38 kg when full).
• Allow adequate clearance for maintenance and service.

2. Mounting the Water Heater:

1. Mark the mounting points on the wall according to the provided template or dimensions.
2. Securely fasten the mounting bracket(s) to the wall using appropriate hardware for the wall type.
3. Carefully lift and hang the water heater onto the mounted bracket(s). Ensure it is level and secure.

3. ජලනල සම්බන්ධතා:

1. Connect the cold water supply line to the inlet pipe (usually marked blue or with a cold water symbol).
2. Connect the hot water output line to the outlet pipe (usually marked red or with a hot water symbol).
3. Install a Temperature and Pressure Relief (TPR) valve according to local codes. Ensure the discharge pipe from the TPR valve is directed downwards and terminates safely.
4. Use appropriate sealants and wrenches to ensure all connections are watertight.

4. ටැංකිය පිරවීම:

1. Before connecting electrical power, open a hot water faucet in your home to allow air to escape.
2. ජල තාපකයට සීතල ජල සැපයුම් කපාටය විවෘත කරන්න.
3. Allow the tank to fill completely until water flows steadily from the hot water faucet. Close the faucet.
4. කාන්දුවීම් සඳහා සියලුම ජලනල සම්බන්ධතා පරීක්ෂා කරන්න.

5. විදුලි සම්බන්ධතාවය:

• පරිපථ කඩනයේ ප්‍රධාන බල සැපයුම අක්‍රිය කර ඇති බවට වග බලා ගන්න.
• Connect the water heater to a dedicated, grounded electrical circuit as specified in the product's electrical requirements (1500W).
• Verify all electrical connections are secure and comply with local electrical codes.

මෙහෙයුම් උපදෙස්

1. මූලික ආරම්භය:

1. Ensure the tank is completely filled with water (refer to "Filling the Tank" in Setup).
2. පරිපථ කඩනයෙහි ජල තාපකයට විදුලි බල සැපයුම ක්‍රියාත්මක කරන්න.
3. LED එල්amp will illuminate, indicating the unit is powered on and beginning to heat water.

2. උෂ්ණත්ව ගැලපීම:

• The TEEE-30DS model features a digital display and/or control knob for temperature adjustment. Refer to the specific controls on your unit.
• Adjust the temperature to your desired setting. A common safe temperature range is 49-54°C (120-130°F) to balance comfort and safety.
• Allow sufficient time for the water to heat up, especially during initial use or after a complete drain.

3. LED Lamp දර්ශකය:

• LED එල්amp indicates the operational status. Typically, it will be lit when the heating element is active and heating water. It may turn off or change color once the set temperature is reached.
• Consult the specific markings on your unit for detailed LED indicator behavior.

4. බලය අක්‍රිය කිරීම:

• To turn off the water heater, switch off the power supply at the circuit breaker.
• For extended periods of inactivity (e.g., vacations), it is recommended to turn off the water heater and drain the tank to prevent stagnant water and potential damage.

නඩත්තු කිරීම

නිතිපතා නඩත්තු කිරීම ප්‍රශස්ත ක්‍රියාකාරිත්වය, බලශක්ති කාර්යක්ෂමතාව සහතික කරන අතර ඔබේ ජල තාපකයේ ආයු කාලය දීර්ඝ කරයි. ඕනෑම නඩත්තුවක් සිදු කිරීමට පෙර සෑම විටම විදුලිය විසන්ධි කරන්න.

1. Draining the Tank (Annually):

1. පරිපථ කඩනයෙහි ජල තාපකයට විදුලිය විසන්ධි කරන්න.
2. Close the cold water supply valve to the water heater.
3. Open a hot water faucet in your home to relieve pressure and allow air into the tank.
4. ජල තාපකයේ පතුලේ ඇති කාණු කපාටයට හෝස් එකක් සම්බන්ධ කර සුදුසු කාණුවකට යොමු කරන්න.
5. Open the drain valve and allow the tank to empty completely. This helps remove sediment buildup.
6. Once drained, close the drain valve, remove the hose, and refill the tank as described in the "Setup" section before restoring power.

2. Inspecting the TPR Valve (Annually):

• Carefully lift the lever on the Temperature and Pressure Relief (TPR) valve to ensure it operates freely and discharges water.
• Allow a small amount of water to flow for a few seconds, then release the lever. If water continues to flow, the valve may need replacement.
• අවවාදයයි: Water discharged will be hot.

3. Anode Rod Inspection/Replacement (Every 3-5 Years):

• The anode rod protects the enamel tank from corrosion. It slowly corrodes over time.
• Consult a qualified technician to inspect and replace the anode rod as needed. This typically involves draining the tank and removing the rod from the top of the heater.

4. බාහිර පිරිසිදු කිරීම:

• Wipe the exterior of the water heater with a soft, damp රෙදි. උල්ෙල්ඛ පිරිසිදු කරන්නන් හෝ ද්රාවණ භාවිතා නොකරන්න.

දෝෂගවේෂණය

සේවාව සම්බන්ධ කර ගැනීමට පෙර, නැවතview මෙම පොදු ගැටළු සහ විසඳුම්.

මෙම විසඳුම් උත්සාහ කිරීමෙන් පසුවද ගැටලුව පවතින්නේ නම්, කරුණාකර බලයලත් සේවා නිලධාරීන් අමතන්න.

පිරිවිතර

වගකීම් සහ සහාය

The TORNADO TEEE-30DS Electric Water Heater comes with a 5-year comprehensive free warranty. මෙම වගකීම් සහතිකය නිෂ්පාදන දෝෂ ආවරණය කරන අතර සාමාන්‍ය භාවිත තත්වයන් යටතේ විශ්වාසනීය ක්‍රියාකාරිත්වය සහතික කරයි.

For warranty claims, technical support, or service inquiries, please contact Tornado customer service. Keep your purchase receipt and product model number (TEEE-30DS) readily available when contacting support.

සටහන: Unauthorized repairs or modifications may void your warranty. Always use authorized service personnel for any repairs.