1. හැඳින්වීම
This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of the Richmat HJA63 Foot Actuator. This actuator is designed as a replacement component for adjustable bed bases, facilitating the movement of the foot section.
2 ආරක්ෂිත තොරතුරු
- Always disconnect power to the adjustable bed base before attempting any installation, maintenance, or repair.
- Ensure all connections are secure and correct before restoring power.
- Do not attempt to modify the actuator or its components.
- ක්රියාත්මක වන අතරතුර අත් සහ ලිහිල් ඇඳුම් චලනය වන කොටස් වලින් ඈත් කර තබා ගන්න.
- This product is designed for specific adjustable bed base applications. Do not use for unintended purposes.
- Refer to the original bed base manufacturer's manual for additional safety guidelines.
3. පැකේජ අන්තර්ගතය
පැකේජය විවෘත කිරීමෙන් පසු සියලුම සංරචක පවතින බවත් හානි නොවී ඇති බවත් තහවුරු කර ගන්න:
- 1 x Richmat HJA63 Foot Actuator
රූපය 3.1: ඉවරයිview of the Richmat HJA63 Foot Actuator. This image shows the complete actuator unit, including the motor housing, linear shaft, and mounting points.
4. පිහිටුවීම සහ ස්ථාපනය
Installation of the Richmat HJA63 Foot Actuator typically involves replacing an existing actuator. Follow these general steps:
- බලය විසන්ධි කරන්න: Unplug the adjustable bed base from the wall outlet to ensure no power is supplied during installation.
- Locate Existing Actuator: Identify the foot actuator on your adjustable bed base. It is usually connected to the frame and the moving foot section.
- රැහැන් විසන්ධි කරන්න: Carefully disconnect the electrical cable from the control box or power supply unit. Note the type of connector.
- Remove Mounting Pins/Bolts: Remove the pins or bolts that secure the actuator to the bed frame at both ends. Keep these fasteners for reinstallation.
- Remove Old Actuator: Carefully slide out the old actuator.
- Install New Actuator: Position the new Richmat HJA63 actuator in the same location. Align the mounting holes.
- Secure Mounting Pins/Bolts: Reinsert and secure the mounting pins or bolts at both ends of the actuator. Ensure they are tight but allow for smooth pivot.
- රැහැන් සම්බන්ධ කරන්න: Connect the electrical cable of the new actuator to the control box or power supply unit. Ensure the 5-pin connector is fully seated.
රූපය 4.1: Richmat HJA63 Actuator showing the 5-pin electrical connector. This connector is used to interface with the bed base's control system.
වැදගත්: Before restoring power, double-check all connections and ensure there are no obstructions around the actuator's path of motion.
5. මෙහෙයුම් උපදෙස්
Once the Richmat HJA63 Foot Actuator is correctly installed and connected, its operation is controlled by the adjustable bed base's remote or control panel. The actuator extends and retracts to raise and lower the foot section of the bed.
- බල ගැන්වීම: Plug the adjustable bed base back into the wall outlet.
- පරීක්ෂණ ක්රියාකාරීත්වය: Use the bed's remote control to slowly raise and lower the foot section. Observe the actuator's movement to ensure it operates smoothly and without obstruction.
- රාජකාරි චක්රය: The actuator has a duty cycle of 10%, maximum 2 minutes ON / 18 minutes OFF. This means it should not be operated continuously for more than 2 minutes at a time, and requires an 18-minute rest period to prevent overheating.
6. නඩත්තු කිරීම
The Richmat HJA63 Foot Actuator is designed for low maintenance. However, periodic checks can help ensure its longevity:
- පිරිසිදු කිරීම: Wipe the exterior of the actuator with a dry or slightly damp රෙදි. දරුණු රසායනික ද්රව්ය හෝ උල්ෙල්ඛ පිරිසිදු කරන්නන් භාවිතා නොකරන්න.
- පරීක්ෂාව: Periodically inspect the mounting points and electrical connections for any signs of wear, looseness, or damage.
- ලිහිසි තෙල්: The internal components are pre-lubricated and do not require additional lubrication.
7. දෝශ නිරාකරණය
If you experience issues with your Richmat HJA63 Foot Actuator, consider the following common troubleshooting steps:
| ගැටලුව | විය හැකි හේතුව | විසඳුම |
|---|---|---|
| Actuator does not move. | No power; Loose connection; Overload; Remote issue. | Check if bed base is plugged in. Ensure all cables are securely connected. Reduce load on bed. Test with another remote if possible, or check remote batteries. |
| Actuator moves slowly or intermittently. | අඩු වෙළුමtage; Overheating; Obstruction. | Ensure stable power supply. Allow actuator to cool down (observe duty cycle). Check for any objects obstructing the actuator's movement. |
| ක්රියාකාරකයෙන් අසාමාන්ය ශබ්දයක්. | Loose mounting; Internal issue. | Check and tighten mounting pins/bolts. If noise persists and is significant, the actuator may require replacement. |
දෝශ නිරාකරණ පියවර මඟින් ගැටළුව විසඳෙන්නේ නැත්නම්, පාරිභෝගික සහාය අමතන්න.
8. පිරිවිතර
Technical specifications for the Richmat HJA63 Foot Actuator:
රූපය 8.1: Product label detailing the specifications of the Richmat HJA63 Actuator. Key information includes model number, voltage, current, load capacity, and duty cycle.
| විශේෂාංගය | විස්තර |
|---|---|
| ආකෘතිය | HJA63 |
| ශ්රේණිගත කළ වෙළුමtage | DC 24V |
| උපරිම ධාරාව | 3.5A උපරිම |
| Max Load (Push) | 6000N |
| ආඝාතය | 80/200 මි.මී |
| රාජකාරි සයිකල් | 10%, Max 2min ON / 18min OFF |
| IP ශ්රේණිගත කිරීම | IP20 |
| සම්බන්ධක වර්ගය | 5-පින් DIN |
9. වගකීම් සහ සහාය
For warranty information or technical support regarding your Richmat HJA63 Foot Actuator, please refer to the documentation provided with your adjustable bed base or contact the manufacturer/seller directly. Keep your purchase receipt as proof of purchase.
For general inquiries or further assistance, please visit the product's listing page or contact the seller through the platform where the purchase was made.
