diymore 18650 Battery Holder Double Li-ion V8 Shield Power Bank Charging Module User Manual

හැඳින්වීම

This manual provides instructions for the diymore 18650 Battery Holder Double Li-ion V8 Shield Power Bank Charging Module. This module is designed to provide portable power for various DIY electronics projects, including those involving Raspberry Pi and Arduino, by utilizing two 18650 Li-ion batteries. It features both 3V and 5V output capabilities and Micro USB charging.

නිෂ්පාදනය අවසන්view

The diymore 18650 Battery Holder Double Li-ion V8 Shield is a compact power solution. It includes a battery holder for two 18650 cells, a Micro USB input for charging, and multiple output pins for 3V and 5V power. An ON/OFF switch controls the power output.

Image: The diymore 18650 Battery Holder Double module with an included Micro USB cable.

රූපය: ඉහළට view of the 18650 Battery Shield V8, highlighting the 5V USB Output, Micro USB input, and Type-C input ports. Note: Batteries are not included.

Image: Detailed diagram of the 18650 Battery Holder Double, indicating the ON/OFF switch, 3V output ports, 5V output ports, USB 5V output, Micro USB, Type-C, and battery polarity markings.

සැකසුම් උපදෙස්

1. බැටරි ස්ථාපනය:

   Insert two 18650 Li-ion batteries into the battery holder. Pay close attention to the positive (+) and negative (-) markings on the board and the batteries. Incorrect installation will damage the module. Ensure the batteries are 65mm in length. The module supports two series-connected 18650 cells (nominal voltage 4.2V each).

   Video: A short demonstration of inserting 18650 batteries into the holder, emphasizing correct polarity and the series connection for external power input.
2. බැටරි ආරෝපණය කිරීම:

   Connect a Micro USB cable to the Micro USB input port on the module. The charging current is approximately 600mA-800mA. The module will charge the installed 18650 batteries.

3. උපාංග වෙත සම්බන්ධ කිරීම:

   Use the designated 3V output ports (1A max) or 5V output ports (2.2A max) to power your electronic projects. The USB 5V output port can also be used for devices requiring 5V power.

මෙහෙයුම් උපදෙස්

1. බල ගැන්වීම / අක්රිය කිරීම:

   Use the ON/OFF switch located on the module to control the power output to connected devices. Ensure the switch is in the "ON" position for power delivery.

2. වෙළුමtage Outputs:
   • The module provides 3V output at up to 1A.
   • The module provides 5V output at up to 2.2A.

   Connect your devices to the appropriate voltage output pins based on their power requirements.
3. අයකිරීමේ තත්වය:

   While charging via Micro USB, the module's indicator lights will show the charging status. Refer to the product's visual diagrams for specific LED indications.

නඩත්තු කිරීම

• මොඩියුලය පිරිසිදුව හා දූවිලි හා තෙතමනයෙන් තොරව තබා ගන්න.
• මොඩියුලය අධික උෂ්ණත්වයට හෝ සෘජු හිරු එළියට නිරාවරණය කිරීමෙන් වළකින්න.
• Regularly inspect battery contacts for corrosion and clean if necessary.
• Ensure batteries are properly seated to maintain good contact.

දෝෂගවේෂණය

• මොඩියුලය ක්‍රියාත්මක නොවේ:

  Check if the 18650 batteries are correctly installed with the right polarity. Ensure the ON/OFF switch is in the "ON" position. Verify that the batteries are charged.

• ප්‍රතිදාන වෙළුම නැතtage:

  Confirm that the module is powered on and batteries are charged. Check all connections to the output ports. Ensure the connected device is not drawing more current than the module's rated output (3V/1A, 5V/2.2A).

• අයකිරීමේ ගැටළු:

  Verify the Micro USB cable and power source are functional. Ensure the charging current is within the 600mA-800mA range. If using protected 18650 cells, ensure they are 65mm in length, as longer cells may not fit or make proper contact.
• ස්වයංක්‍රීය වසා දැමීම:

  The module may have an automatic shutdown feature if the load is too low (e.g., less than 90mA) for an extended period. This is a design feature to conserve battery power. For very low-power applications, consider if this feature is compatible with your project's requirements.

පිරිවිතර

වගකීම් සහ සහාය

For warranty information and technical support, please refer to the seller's policies on the platform where the product was purchased. Keep your purchase receipt for any warranty claims.