GODIYMODULES MCU-20948-001 6-Axis 6DOF චලන ලුහුබැඳීමේ සංවේදක මොඩියුල පරිශීලක අත්පොත

1. හැඳින්වීම

This manual provides detailed instructions for the installation, operation, and maintenance of the GODIYMODULES MCU-20948-001 6-Axis 6DOF Motion Tracking Sensor Module. This module integrates an accelerometer and gyroscope, supporting both I2C and SPI communication protocols, and is designed for various motion tracking applications, particularly with Arduino-based systems.

2. නිෂ්පාදන ලක්ෂණ

• Integrated 6-Axis (Accelerometer + Gyroscope) motion tracking.
• Supports both I2C and SPI digital communication interfaces.
• අඩු බලශක්ති පරිභෝජනය නිර්මාණය.
• පුළුල් මෙහෙයුම් වෙළුමtage පරාසය: 1.71V සිට 3.6V දක්වා.
• Compact module design for easy integration into projects.
• Compatible with Arduino-based development platforms.

3. තාක්ෂණික පිරිවිතර

4. පිහිටුවීම සහ සම්බන්ධ කිරීම

This section details the physical connections required to integrate the MCU-20948-001 sensor module into your project.

4.1 පින්අවුට් රූප සටහන

The image above displays the pin configuration of the MCU-20948-001 module. Understanding these pins is essential for correct wiring.

4.2 බල සැපයුම

• සම්බන්ධ කරන්න VCC pin to a power source within the range of 1.71V සිට 3.6V දක්වා.
• සම්බන්ධ කරන්න GND pin to the ground of your system.
• අවවාදයයි: පරිමාවක් යෙදීමtage higher than 3.6V, such as 5V, can permanently damage the sensor module.

4.3 සන්නිවේදන අතුරුමුහුණත

The module supports both I2C and SPI communication. Select the appropriate interface based on your project requirements.

4.3.1 I2C Connection

• සම්බන්ධ කරන්න SCL to your microcontroller's I2C Clock pin.
• සම්බන්ධ කරන්න SDA to your microcontroller's I2C Data pin.
• The default I2C address is typically 0x69 or 0x68, depending on the state of the ADO pin.

4.3.2 SPI Connection

• සම්බන්ධ කරන්න SCL to your microcontroller's SPI Clock (SCK) pin.
• සම්බන්ධ කරන්න SDA to your microcontroller's SPI Master Out Slave In (MOSI) pin.
• සම්බන්ධ කරන්න ADO to your microcontroller's SPI Master In Slave Out (MISO) pin.
• සම්බන්ධ කරන්න NCS to your microcontroller's Chip Select (CS) pin.

5. මෙහෙයුම් උපදෙස්

After successfully connecting the module, you can begin programming your microcontroller to read data from the sensor.

5.1 Software Libraries and Code

• For Arduino-based systems, specific libraries are required to interface with the MCU-20948-001 (ICM-20948) sensor. ඒ සඳහා සොයන්න "ICM-20948 Arduino library" in the Arduino IDE Library Manager or online.
• The register map and communication protocols for the ICM-20948 differ from older sensors like the MPU-9250. Ensure you use libraries and code specifically designed for the ICM-20948 to avoid compatibility issues.
• Refer to the documentation provided with your chosen library for example code and detailed usage instructions.

5.2 දත්ත අත්පත් කර ගැනීම

Once the library is integrated, you can initialize the sensor and read accelerometer and gyroscope data. The sensor provides raw data which may require calibration and filtering for accurate motion tracking.

• ත්වරණමාන: Measures linear acceleration along X, Y, and Z axes.
• ගයිරෝස්කෝප්: Measures angular velocity (rotation rate) around X, Y, and Z axes.

6. නඩත්තු කිරීම

The MCU-20948-001 sensor module is a low-maintenance device. Follow these guidelines to ensure its longevity:

• මොඩියුලය පිරිසිදුව හා දූවිලි හා තෙතමනයෙන් තොරව තබා ගන්න.
• මොඩියුලය අධික උෂ්ණත්වයට හෝ සෘජු හිරු එළියට නිරාවරණය කිරීමෙන් වළකින්න.
• Handle the module with care to prevent physical damage to the components or solder joints.
• Ensure proper ventilation if enclosed in a casing to prevent overheating.

7. දෝශ නිරාකරණය

If you encounter issues with your MCU-20948-001 module, consider the following common problems and solutions:

• Module Not Responding / No Data:
  • Verify power connections (VCC and GND) and ensure the voltage is between 1.71V and 3.6V. A 5V supply will damage the module.
  • Check communication wiring (SCL, SDA for I2C; SCL, SDA, ADO, NCS for SPI) for correct connections and continuity.
  • Confirm the correct I2C address (0x68 or 0x69) is being used in your code.
  • Ensure the correct software library for the ICM-20948 is installed and properly configured. Libraries for MPU-9250 are not compatible.
• වැරදි කියවීම්:
  • Perform sensor calibration routines if available in your chosen library.
  • Ensure the module is securely mounted and not subject to vibrations or external magnetic interference (if using a magnetometer, though this module is 6-axis).
• Magnetometer Not Working (if applicable):
  • While this product is advertised as 6-axis, some ICM-20948 chips include a magnetometer. If your specific chip has one and it's not working, ensure the magnetometer is enabled and correctly addressed in your software. Some breakout boards might not expose all 9-axis functionality or require specific initialization.

8 ආරක්ෂිත තොරතුරු

• Do not exceed the specified operating voltage (1.71V to 3.6V). Overvoltage will damage the module.
• Avoid short-circuiting the pins.
• Keep the module away from water, corrosive liquids, and extreme temperatures.
• This product contains small components and should be kept out of reach of children.
• If you are unsure about any connection or operation, consult relevant technical documentation or seek professional assistance.

9. වගකීම් සහ සහාය

For technical support or inquiries regarding the GODIYMODULES MCU-20948-001 sensor module, please refer to the seller's contact information or the product listing page where you purchased the item. Specific warranty details may vary by retailer.