GODIYMODULES Dual NE5532 Preamplifier මණ්ඩල උපදෙස් අත්පොත

හැඳින්වීම

This manual provides essential information for the proper setup, operation, and maintenance of your GODIYMODULES Dual NE5532 Preamplifier Board. This pre-amplifier is designed with two NE5532 operational amplifiers, dedicating one amplifier per channel for enhanced audio performance compared to single operational amplifier designs. It features a built-in single power supply to dual power supply chip, allowing it to function with a single power input while providing dual power supply characteristics internally. The board incorporates large-capacity filter capacitors and a rectifier circuit, enabling compatibility with both AC and DC power sources.

ප්‍රශස්ත කාර්ය සාධනය සහ දීර්ඝ ආයුෂ සහතික කිරීම සඳහා නිෂ්පාදිතය භාවිතා කිරීමට පෙර කරුණාකර මෙම අත්පොත හොඳින් කියවන්න.

ආරක්ෂිත තොරතුරු

• සෑම විටම බල සැපයුමේ පරිමාව සහතික කරන්නtage and polarity are correct before connecting to the board. Incorrect voltage or polarity can damage the device.
• Avoid touching electronic components while the board is powered to prevent electric shock or damage to sensitive parts.
• Do not expose the board to moisture, extreme temperatures, or static electricity.
• සංරචක හෝ පෑස්සුම් සන්ධිවලට භෞතික හානි වැළැක්වීම සඳහා පුවරුව ප්‍රවේශමෙන් හසුරුවන්න.
• If you are unsure about any installation or operation step, consult a qualified technician.

පැකේජයේ අන්තර්ගතය

ඔබගේ පැකේජයේ සියලුම අයිතම ඇති බව තහවුරු කරගන්න:

• 1 x Dual NE5532 Preampජීවිතාරක්ෂක මණ්ඩලය
• 2 x Signal Lines

Image: The Dual NE5532 Preamplifier Board shown with the two included signal lines.

සැලසුම

1. බල සැපයුම් සම්බන්ධතාවය

පෙරamplifier board supports a wide range of power inputs:

• ඒසී වෙළුමtage: 5V සිට 16V දක්වා
• ඩීසී වෙළුමtage: 6V සිට 24V දක්වා

Connect your power source to the designated power input terminals on the board. Ensure correct polarity for DC power. The board is designed with a rectifier circuit and filter capacitors for stable operation with both AC and DC inputs.

රූපය: අවසන්view පෙරamplifier board, highlighting power input (blue terminal block on the left) and audio connections.

2. Audio Input and Output Connections

Connect your audio source (e.g., microphone, audio player) to the "IN" terminals (L, GND, R) and your audio output device (e.g., amplifier, speakers) to the "OUT" terminals (L, GND, R). Use the provided signal lines or appropriate audio cables.

3. Magnification Adjustment (Optional)

The board features R1 and R5 as magnification setting resistors. The default magnification is approximately 5 times. You can adjust the magnification by changing these resistors.

• ප්රතිරෝධක පරාසය: 5kΩ to 100kΩ.
• A larger resistance value will result in higher magnification.
• If using plug-in resistors, carefully remove the original surface-mount chip resistors by soldering and then solder the new plug-in resistors onto the pads at both ends of the patch position.

රූපය: විස්තරාත්මක view of the board. R1 and R5 resistors are located near the NE5532 operational amplifier chips, allowing for magnification adjustment.

මෙහෙයුම් උපදෙස්

1. පවර් ඔන්

Once all connections (power, audio input, audio output) are securely made, apply power to the board. An LED indicator (if present) should illuminate, indicating the board is powered.

2. වෙළුම් පාලනය

Adjust the potentiometer (rotary knob) on the board to control the output volume. Start with the volume at a low setting and gradually increase it to your desired level to avoid sudden loud sounds.

3. ශ්රව්ය ප්ලේබැක්

Begin playing audio from your connected source. The preamplifier will boost the signal before sending it to your output device.

නඩත්තු කිරීම

• Keep the board clean and free from dust. Use a soft, dry brush or compressed air for cleaning.
• සියලුම සම්බන්ධතා ආරක්ෂිත බව සහතික කිරීම සඳහා වරින් වර පරීක්ෂා කරන්න.
• Store the board in a dry, cool environment when not in use.
• The NE5532 operational amplifier chips are socketed, allowing for easy replacement or upgrade with other pin-compatible ICs if desired.

දෝෂගවේෂණය

• ශබ්දයක් නැත:
  • Check all power and audio connections. Ensure they are firmly seated and correctly wired.
  • Verify the power supply is providing the correct voltage (AC 5-16V or DC 6-24V).
  • Ensure the audio source is playing and the output device is powered on and set to the correct input.
  • Adjust the volume potentiometer on the board.
• Hum or Hissing Noise:
  • Check for proper grounding of all audio components.
  • Ensure audio cables are shielded and not running parallel to power cables.
  • Move the unit or cabling away from potential sources of electromagnetic interference (RFI), such as power transformers, motors, or wireless devices.
  • Verify the power supply is stable and free from ripple.
• විකෘති ශබ්දය:
  • Reduce the input signal level if it is too high.
  • Check the magnification setting (R1, R5 resistors); if it's too high for your application, consider reducing it.
  • Ensure the output device (e.g., amplifier) is not overdriven.

පිරිවිතර

වගකීම් සහ සහාය

For warranty information and technical support, please refer to the seller's policies or contact GODIYMODULES directly through their official channels. Keep your purchase receipt as proof of purchase.