1. හැඳින්වීම
This manual provides instructions for the safe and effective use of the SparkFun JST Battery Removal Tool. This tool is designed to facilitate the disconnection of standard 2-pin JST-PH connectors (2mm pitch) from their housings, particularly useful for LiPo battery connections.
The tool helps prevent damage to wires and connectors, and avoids discomfort to fingers during the disconnection process.
Figure 1: The SparkFun JST Battery Removal Tool. This image shows the black, 3D-printed tool with the SparkFun logo and a keychain hole, designed for safely disconnecting JST-PH connectors.
2 ප්රධාන ලක්ෂණ
- Designed for standard 2-pin JST-PH connectors (2mm pitch).
- Protects fingers and wires during disconnection.
- Integrated keychain hole for portability and storage.
- Features a wire channel for downward sliding removal against a surface.
- Suitable for users who frequently swap LiPo batteries.
3. පිහිටුවීම
The SparkFun JST Battery Removal Tool requires no assembly or complex setup. It is ready for use directly out of the packaging.
Ensure the tool is clean and free of debris before use to prevent any interference with the connector.
4. මෙහෙයුම් උපදෙස්
Follow these steps to safely disconnect a 2-pin JST-PH connector using the tool:
- සම්බන්ධකය හඳුනා ගන්න: Locate the 2-pin JST-PH female connector (typically on the battery) and the corresponding male connector (typically on the board or device).
- මෙවලම ස්ථානගත කරන්න: Hold the SparkFun JST Battery Removal Tool in one hand. Slide the tool over the JST-PH female connector. The tool is designed to slide from either the top or bottom side of the connector.
- Grip the Male Connector: With your other hand, firmly hold the male connector on the board to provide stability.
- විසන්ධි කරන්න: Gently pull the JST female connector away from the male connector using the tool. The tool's internal "triangle blocks" are designed to grip the wings of the female connector, aiding in its removal.
- Alternative Method (Wire Channel): If disconnecting against a flat surface, you may slide the tool downward, utilizing the integrated wire channel to accommodate the battery wires.
වැදගත් සටහන:
- This tool is not intended for inserting a JST female connector into a male connector. Insertion should be done manually.
- Obstruction Warning: The tool works best when the JST male connector is populated on the edge of a board. Certain board designs with the JST male connector facing inward or with nearby components may obstruct the tool's use.
5. නඩත්තු කිරීම
The SparkFun JST Battery Removal Tool requires minimal maintenance:
- පිරිසිදු කිරීම: Wipe the tool with a dry, soft cloth to remove any dust or debris. Do not use harsh chemicals or abrasive materials.
- ගබඩා: Store the tool in a dry place, away from direct sunlight and extreme temperatures. The keychain hole allows for convenient storage with other tools or on a hook.
- පරීක්ෂාව: Periodically inspect the tool for any signs of wear or damage. While 3D printed, it is designed for durability, but excessive force or improper use can cause damage.
6. දෝශ නිරාකරණය
| ගැටලුව | විය හැකි හේතුව | විසඳුම |
|---|---|---|
| Tool does not slide over connector easily. | Misalignment; Obstruction from board components. | Ensure the tool is aligned correctly with the JST-PH female connector. Check if surrounding components on the board are blocking the tool. The tool may not be suitable for all board layouts. |
| Connector is difficult to remove even with the tool. | Connector is very tight; Incorrect pulling angle. | Apply steady, firm pressure. Ensure you are pulling straight away from the male connector. Avoid twisting. |
| Tool appears damaged or has imperfections. | Manufacturing variation (3D printed); Physical stress. | Minor imperfections are normal for 3D printed parts. If functionality is affected, contact SparkFun support. Avoid applying excessive force. |
7. පිරිවිතර
- නිෂ්පාදන නම: SparkFun JST Battery Removal Tool
- Compatible Connector Type: Standard 2-pin JST-PH (2mm pitch)
- මානයන් (L x W x H): 35mm x 16mm x 9mm (අඟල් 1.38 x 0.71 x 0.39)
- බර: ආසන්න වශයෙන් ග්රෑම් 3.15 (අවුන්ස 0.11)
- ද්රව්ය: 3D Printed Polymer
- විශේෂාංග: Keychain hole, Wire channel
8. වගකීම් තොරතුරු
For information regarding warranty coverage and terms for SparkFun products, please refer to the official SparkFun Electronics webවෙබ් අඩවියට හෝ ඔවුන්ගේ පාරිභෝගික සහාය සෘජුවම අමතන්න. වගකීම් කොන්දේසි සාමාන්යයෙන් නිෂ්පාදන දෝෂ ආවරණය කරයි.
9. සහාය සහ සම්බන්ධතා තොරතුරු
If you encounter issues or have questions not covered in this manual, please contact SparkFun Electronics support:
- Webඅඩවිය: www.sparkfun.com
- උපකාරක පිටුව: Refer to the support section on the SparkFun website for FAQs, forums, and contact options.
