BUUBO BM410 කාර් බැටරි පරීක්ෂක පරිශීලක අත්පොත

1. හැඳින්වීම

The BUUBO BM410 Car Battery Tester is a versatile diagnostic tool designed to assess the health and performance of 12V and 24V automotive batteries, as well as the vehicle's charging and cranking systems. This manual provides detailed instructions for safe and effective use of the device.

2 ආරක්ෂිත තොරතුරු

Always observe the following safety precautions when working with automotive batteries:

• Wear appropriate eye protection and gloves.
• Ensure adequate ventilation to prevent accumulation of explosive gases.
• Avoid sparks or open flames near the battery.
• Do not touch battery acid. If contact occurs, flush immediately with water and seek medical attention.
• Connect the tester correctly: රතු clamp to positive (+) terminal, කළු clamp to negative (-) terminal. The BM410 features reverse connection protection, but correct connection is always recommended.
• ළමයින් සහ අනවසර පුද්ගලයින් වැඩ කරන ස්ථානයෙන් ඈත් කරන්න.

3. නිෂ්පාදන අවසන්view

The BUUBO BM410 is a compact and easy-to-use battery tester. It features an LED display for clear indication of test results and robust alligator clips for secure connection.

රූප විස්තරය: උඩිස් වැඩකි view of the BUUBO BM410 Car Battery Tester. Key components are labeled: Cables, LED Display, Battery Condition indicators, Alternator States indicators, BUUBO logo, Positive Clip (red), and Negative Clip (black). This image illustrates the physical layout of the device.

The device automatically identifies 12V or 24V systems, simplifying operation. It supports two primary modes: battery loaded in the car and unloaded battery testing.

රූප විස්තරය: A graphic highlighting the features of the Car Battery Tester BM410 & BM310. It explicitly states 'SUPPORT 12V & 24V' and 'LED Lights', emphasizing the device's compatibility with different voltage systems and its visual indicators.

4. පිහිටුවීම

Before performing any test, ensure the vehicle is turned off and the ignition is in the OFF position, unless otherwise specified for a particular test.

1. බැටරි පර්යන්ත පිරිසිදු කරන්න: Ensure the battery terminals are clean and free from corrosion for accurate readings.
2. Cl සම්බන්ධ කරන්නamps: අමුණන්න රතු (+) clamp ධනාත්මක බැටරි පර්යන්තයට සහ කළු (-) clamp to the negative battery terminal. The device will power on automatically.

රූප විස්තරය: A detailed diagram illustrating the correct connection of the battery tester to a car battery. It shows the red alligator clip connecting to the positive (+) terminal and the black alligator clip connecting to the negative (-) terminal. Text labels indicate 'To battery "-" Negative' and 'To battery "+" Positive'. This image is essential for proper setup.

5. මෙහෙයුම් උපදෙස්

The BM410 offers several diagnostic functions. Use the 'LOADING TEST' and 'BATTERY TEST' switch to select the desired mode.

රූප විස්තරය: සමීප රූපයක් view of the BUUBO BM410's LED display, detailing the indicators for both 'Loading Test' and 'Charging Test'. It shows different LED states (Full, Middle, Low, OK, Fault, Good) and their corresponding meanings for 12V and 24V systems, along with the function switch.

5.1. Battery Test (Load Test)

This test assesses the battery's ability to hold a charge under a simulated load.

1. Ensure the tester is connected to the battery.
2. Set the switch to 'BATTERY TEST'.
3. Observe the 'Battery State' LEDs.

5.2. ආරෝපණ පද්ධති පරීක්ෂණය

මෙම පරීක්ෂණය මඟින් ප්‍රත්‍යාවර්තකය ඇතුළුව වාහනයේ ආරෝපණ පද්ධතිය ඇගයීමට ලක් කරයි.

1. Ensure the tester is connected to the battery.
2. වාහනයේ එන්ජිම පණ ගන්වන්න.
3. Accelerate the engine to approximately 2000 RPM.
4. Observe the 'Alternator State' LEDs. A 'Good' indication means the charging circuit is normal. A 'Fault' indication (especially if the alternator voltage is too high) suggests a potential issue that could damage the battery.

5.3. Pre-Charging Check

This check determines if a battery can accept a charge.

1. Ensure the tester is connected to the battery.
2. එන්ජිම නිවා දමන්න.
3. Observe the 'Check Before Charging' LED. An 'OK' light indicates the battery can be charged. If the voltage drops below 10V, the battery may be damaged and unable to accept a charge.

6. LED දර්ශක අවබෝධ කර ගැනීම

The BM410 uses a series of LED lights to provide clear and immediate feedback on the battery and charging system status.

6.1. Battery State Indicators (for Battery Test)

• Full (Green): Battery is in good condition with good loading level.
• Middle (Yellow): Battery is in normal condition with normal loading level.
• Low (Red): Battery is in bad condition with bad loading level.

6.2. Alternator State Indicators (for Charging System Test)

• Good (Green): Alternator is functioning correctly, and the charging circuit is normal.
• Fault (Red): Indicates an issue with the alternator or charging system. This could mean the voltage ඉතා ඉහළ හෝ ඉතා අඩු ය.

6.3. Check Before Charging Indicator

• OK (Green): Battery can be charged.
• Low (Red): Battery is too low and may need re-charge, or is potentially damaged if voltagඊ 10V ට අඩුයි.

6.4. වෙළුමtage Indicators (12V/24V)

• 12V (Green): Current battery is 12V.
• 24V (රතු): Current battery is 24V.

7. දෝශ නිරාකරණය

If you encounter issues while using the BM410, consider the following:

• බලය නැත/සංදර්ශකයක් නැත: cl සහතික කරන්නamps are securely connected to the correct battery terminals. Check for corrosion on battery terminals that might prevent a good connection.
• වැරදි කියවීම්: Ensure battery terminals are clean. The battery should be at a stable temperature for best results.
• 'Fault' on Alternator Test: This indicates a problem with the vehicle's charging system. Consult a qualified mechanic for further diagnosis.
• 'Low' on Check Before Charging: බැටරි පරිමාව නම්tage is extremely low (e.g., below 10V), the battery may be deeply discharged or damaged and might not accept a charge.

8. පිරිවිතර

9. නඩත්තු කිරීම

To ensure the longevity and accuracy of your BUUBO BM410 Car Battery Tester:

• Keep the device clean and dry. Wipe with a soft, damp අවශ්ය නම් රෙදි.
• සෘජු හිරු එළියෙන් සහ අධික උෂ්ණත්වයන්ගෙන් ඈත්ව සිසිල් වියළි ස්ථානයක ගබඩා කරන්න.
• Inspect the cables and clamps regularly for any signs of damage or wear. Replace if necessary.

10. වගකීම් සහ සහාය

වගකීම් තොරතුරු හෝ තාක්ෂණික සහාය සඳහා, කරුණාකර නිෂ්පාදන ඇසුරුම්කරණය වෙත යොමු වන්න හෝ නිෂ්පාදකයා කෙලින්ම අමතන්න. මිලදී ගැනීමේ සාක්ෂියක් ලෙස ඔබේ මිලදී ගැනීමේ රිසිට්පත තබා ගන්න.