1. නිෂ්පාදන අවසන්view
The ZFX W1209A is a high-precision digital temperature controller designed for a wide range of applications requiring accurate temperature management. It features a clear 3-digit LED display, an NTC waterproof probe for fluid temperature control, and a robust 30A relay output. This manual provides essential information for the proper setup, operation, and maintenance of your W1209A temperature controller.
රූපය 1: ප්රධාන view of the ZFX W1209A Digital Temperature Controller, showing the green PCB, LED display, control buttons, and terminal blocks.
2 ප්රධාන ලක්ෂණ
- High Precision and Wide Measurement Range: Capable of measuring and controlling temperatures from -50°C to 110°C with 0.1°C accuracy.
- Waterproof NTC Probe: Includes a durable NTC 10K waterproof sensor, suitable for controlling fluid temperatures.
- Easy Installation and Operation: Designed for straightforward setup and user-friendly control.
- පැහැදිලි LED සංදර්ශකය: Features a bright 0.7-inch 3-digit LED display for easy temperature monitoring.
- ස්ථාවර කාර්ය සාධනය: Engineered for reliable and long-term operation.
- ඉහළ ධාරා ප්රතිදානය: Equipped with a 30A relay for controlling high-power loads.
Figure 2: The W1209A controller highlighting its digital display and control range of -50°C to 110°C.
3. සැකසීම සහ රැහැන්වීම
Before connecting, ensure all power sources are disconnected. Refer to the wiring diagram below for correct connections. Incorrect wiring can damage the device or connected equipment.
- Power Supply (12V DC): Connect a 12V DC power source to the two terminals labeled "12V Power Supply". Ensure correct polarity (positive to '+' and negative to '-').
- NTC සංවේදකය: Plug the NTC waterproof temperature probe into the "Sensor Socket" connector.
- රිලේ ප්රතිදානය: Connect the device you wish to control (e.g., heater, cooler) to the "Relay Output" terminals. This is a dry contact relay, meaning it acts as a switch. You will need to provide power to your controlled device separately, routed through these relay contacts. The relay can handle up to 30A.
Figure 3: Detailed wiring diagram of the W1209A controller, showing connections for the sensor, 12V DC power supply, and relay output.
After all connections are made, you can apply 12V DC power to the controller. The LED display will show the current temperature measured by the NTC probe.
4. මෙහෙයුම් උපදෙස්
The W1209A controller has three buttons: SET, UP, and DOWN.
4.1. Setting the Target Temperature
- ඔබන්න සකසන්න button once. The display will flash, indicating the current target temperature.
- භාවිතා කරන්න UP සහ පහළට buttons to adjust the target temperature to your desired value.
- ඔබන්න සකසන්න සැකසුම තහවුරු කර සුරැකීමට නැවතත් ක්ලික් කරන්න, නැතහොත් එය ස්වයංක්රීයව සුරැකීමට තත්පර කිහිපයක් රැඳී සිටින්න.
4.2. Accessing Parameter Settings (P0-P6)
To access advanced settings, press and hold the සකසන්න button for approximately 5 seconds. The display will show "P0". Use the UP සහ පහළට buttons to navigate through the parameters (P0 to P6).
Once you select a parameter (e.g., P0), press සකසන්න නැවතත් වෙත view its current value. Use UP සහ පහළට අගය වෙනස් කිරීමට. ඔබන්න සකසන්න to confirm the new value and return to the parameter list, or hold සකසන්න to exit all settings.
පරාමිති විස්තර:
- P0: Cooling/Heating Mode (C/H)
- H (Heating Mode): The relay closes when the current temperature is below the set temperature minus the hysteresis. It opens when the current temperature reaches the set temperature.
- C (Cooling Mode): The relay closes when the current temperature is above the set temperature plus the hysteresis. It opens when the current temperature reaches the set temperature.
- P1: Hysteresis Setting (0.1-30°C)
Sets the difference between the turn-on and turn-off temperatures to prevent rapid cycling of the relay. - P2: Upper Limit of Temperature Setting (110°C)
Defines the maximum adjustable target temperature. - P3: Lower Limit of Temperature Setting (-50°C)
Defines the minimum adjustable target temperature. - P4: Temperature Correction (-7.0 to 7.0°C)
Allows for calibration of the temperature reading if there is a discrepancy with a known accurate thermometer. - P5: Delay Start Time (0-10 minutes)
Sets a delay before the relay activates after the temperature condition is met. Useful for compressors or other equipment that requires a delay. - P6: High Temperature Alarm (0-110°C)
If the current temperature exceeds this value, the display will show "HHH" and the relay will disconnect.
4.3. කර්මාන්තශාලා සැකසුම් ප්රතිස්ථාපනය කිරීම
To restore the controller to its factory default settings, power off the device. Then, press and hold both the UP සහ පහළට buttons simultaneously while powering on the device. The display will show "888" to confirm the reset.
5. පිරිවිතර
Figure 4: Dimensions of the ZFX W1209A controller, measuring approximately 75.5mm x 45mm.
| පරාමිතිය | වටිනාකම |
|---|---|
| ආකෘතිය | ZFX-W1209A |
| ආදාන වෙළුමtage | DC 12V |
| ප්රතිදානය | 30A රිලේ |
| උෂ්ණත්ව පාලන පරාසය | -50°C ~ 110°C |
| උෂ්ණත්වය මැනීමේ නිරවද්යතාව | 0.1°C |
| පාලන නිරවද්යතාව | 0.1°C |
| Refresh Rate | තත්පර 0.5 යි |
| උෂ්ණත්ව සංවේදකය | NTC 10K (300mm length) |
| ඉහළ උෂ්ණත්ව ආරක්ෂණය | 0°C ~ 110°C (P6 setting) |
| මෙහෙයුම් පරිසර උෂ්ණත්වය | -10°C ~ 60°C |
| මෙහෙයුම් පරිසර ආර්ද්රතාවය | 20% ~ 85% |
| මානයන් | 75.5mm x 45mm |
| පැකේජයේ අන්තර්ගතය | 1 Temperature Controller with Probe |
6. දෝශ නිරාකරණය
- Display shows "LLL": Indicates the sensor is disconnected or damaged. Check the sensor connection or replace the sensor.
- Display shows "HHH": Indicates the measured temperature exceeds the upper limit (P6 setting) or the sensor is short-circuited. Check the sensor and the P6 setting.
- Display shows "---": Indicates the controller is in high-temperature protection mode (P6 activated) or the temperature is below the lower limit.
- පාලකය ක්රියාත්මක නොවේ: Verify the 12V DC power supply connection and ensure correct polarity. Check the power source itself.
- රිලේ සක්රිය නොවේ:
- Check if the target temperature and current temperature conditions are met for the selected heating/cooling mode (P0).
- Verify the hysteresis setting (P1).
- Check if a delay start time (P5) is active.
- Ensure the controlled device is properly wired to the relay output and has its own power supply.
- වැරදි උෂ්ණත්ව කියවීම්: Use the temperature correction parameter (P4) to calibrate the sensor against a known accurate thermometer.
7. නඩත්තු කිරීම
The ZFX W1209A temperature controller requires minimal maintenance. Keep the device clean and free from dust and moisture. Ensure all connections are secure. Avoid exposing the controller to extreme temperatures or corrosive environments beyond its specified operating range.
8. වගකීම් සහ සහාය
Specific warranty information for this product is not provided in the available documentation. For support or warranty inquiries, please contact your retailer or the manufacturer directly with your purchase details.
