M5STACK ඒකකය C6L බුද්ධිමත් දාර පරිගණක ඒකක හිමිකරුගේ අත්පොත
Unit C6L is an intelligent edge computing unit integrated with the M5Stack_Lora_C6module — featuring an Espressif ESP32-C6 SoC and Semtech SX1262 LoRa transceiver — and engineered with a modular design for long-range, low-power LoRaWAN communication alongside high-speed 2.4 GHz Wi-Fi and BLE connectivity.
It includes a 0.66″ SPI OLED display for real-time data visualization, a WS2812Caddressable RGB LED for system-status indication, a built-in buzzer for audible alerts, and front-panel buttons (SYS_SW) with a reset switch for local interaction. Astandard Grove I²C interface allows seamless integration with M5Stack hosts and various Grove sensors. The onboard USB Type-C port supports ESP32- C6 firmware programming, serial debugging, and 5 V power input, while automatic power switching and multi-channel ESD/surge protection ensure stable operation. Unit C6L excels at real-time data acquisition, edge-intelligence processing, and remote control, making it ideal for IoT applications such as smart agriculture, environmental monitoring, industrial IoT, smart buildings, asset tracking, and urban infrastructure sensing.\
1.1. ඒකකය C6L
- සන්නිවේදන හැකියාවන්
Integrated LoRa (Semtech SX1262), supporting LoRaWAN Class A/B/Candpointto-point modes 2.4 GHz Wi-Fi and BLE via ESP32-C6-MINI-1U - සකසනය සහ කාර්ය සාධනය
Main Controller: Espressif ESP32-C6 (single-core RISC-V, up to 40 MHz) On-chip Memory: 512 KB SRAM with integrated ROM - විදුලිබල හා බලශක්ති කළමනාකරණය
Power Input: USB Type-C (5 V input) and Grove 5 V input - සංදර්ශකය සහ දර්ශක
0.66″ SPI OLED display for real-time data visualization and status monitoringWS2812C addressable RGB LED for system-status indication Built-in buzzer for audible alerts - Interfaces & Controls
Grove I²C interface (with 5 V power) for seamless connection to M5Stack hostsandGrove sensors USB Type-C port for firmware programming, serial debugging, and power input Front-panel buttons (SYS_SW) and reset switch (MCU_RST) for local control - Expansion & Debug Pads
Bootloader pad: predefined jumper pad for entering bootloader mode Test points (TP1–TP8) for signal probing and in-circuit debug
2. පිරිවිතර
පරාමිතිය | පිරිවිතර |
MCU | Espressif ESP32-C6(තනි-හර RISC-V, 40 MHz දක්වා) |
සන්නිවේදනය | LoRaWAN; 2.4 GHz Wi-Fi BLE |
බල ආදානය | USB වර්ගය-C(5V) සහ ග්රෝව් 5V |
සැපයුම් වෙළුමtage | 3.3 V (පුවරුවේ LDO) |
ෆ්ලෑෂ් ගබඩාව | 16 MB SPI ෆ්ලෑෂ් (128 Mbit) |
ප්රදර්ශනය කරන්න | 0.66”SPI OLED(128×64) |
දර්ශකය | WS2812C ආමන්ත්රණය කළ හැකි RGB LED |
බසර් | යානය තුළ ඇති බසරය |
බොත්තම් | System button (SYS_SW)and reset button(MCU_RST) |
අතුරුමුහුණත් | ග්රෝව් I²C;USB වර්ගය-C; බූට්ලෝඩර් පෑඩ්;TP1-TP8 නිදොස් කිරීමේ පෑඩ් |
ඇන්ටනා | 2×SSMB-JEF clamp සම්බන්ධක;2×IPEX-4 ඇන්ටෙනා සම්බන්ධක |
මෙහෙයුම් උෂ්ණත්වය | මෙහෙයුම් උෂ්ණත්වය |
අමතර විශේෂාංග | Multi-channel ESD/surge protection |
නිෂ්පාදකයා | M5Stack Technology Co., Ltd Block A10, Expo Bay South Coast, Fuhai Street, Bao’an District, Shenzhen, China |
Frequency Range for CE | 2.4G Wi-Fi: 2412-2472MHz BLE: 2402-2480MHz Lora: 868-868.6MHz |
CE සඳහා උපරිම EIRP | BLE: 5.03dBm 2.4G Wi-Fi: 16.96dBm Lora: 9.45dBm |
ග්රාහක කාණ්ඩය | The equipment provider declared that the receiver category for the EUTis2. |

3. FCC අනතුරු ඇඟවීම
FCC අවවාදය:
අනුකූලතාව සඳහා වගකිව යුතු පාර්ශ්වයෙන් පැහැදිලිවම අනුමත නොකළ ඕනෑම වෙනස්කමක් හෝ වෙනස් කිරීමක් උපකරණය ක්රියාත්මක කිරීමට පරිශීලකයාගේ අධිකාරිය අවලංගු කළ හැකිය. මෙම උපාංගය FCC රීතිවල 15 කොටසට අනුකූල වේ. මෙහෙයුම පහත කොන්දේසි දෙකට යටත් වේ: (1) මෙම උපාංගය හානිකර මැදිහත්වීම් ඇති නොකළ හැකිය, සහ (2) මෙම උපාංගය අනවශ්ය ලෙස ක්රියා කිරීමට හේතු විය හැකි මැදිහත්වීම් ඇතුළුව ලැබෙන ඕනෑම බාධාවක් පිළිගත යුතුය.
වැදගත් සටහන:
සටහන: This equipment has been tested and found to comply with the limits for a ClassBdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
පහත සඳහන් පියවරයන්ගෙන් එකක් හෝ වැඩි ගණනකින් ඇඟිලි ගැසීම් නිවැරදි කරන්න:
- ලැබෙන ඇන්ටනාව නැවත දිශානතියට පත් කිරීම හෝ නැවත ස්ථානගත කිරීම.
- Increase the separation betweentheequipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.
I. Installing Arduino IDE(https://www.arduino.cc/en/Main/Software)
Arduino නිලධාරියා වෙත යාමට ක්ලික් කරන්න webඅඩවිය , සහ ඔබේ ස්ථාපන පැකේජය තෝරන්න
operating system to download. Ⅱ. Installing Arduino Board Management
1. මණ්ඩල කළමනාකරු URL is used to index the development board information for specific platform. In the Arduino IDE menu, select File -> මනාප
2. ESP පුවරු කළමනාකරණය පිටපත් කරන්න URL අතිරේක මණ්ඩල කළමනාකරු වෙත පහතින්
URLs: field, and save.
https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. පැති තීරුවේ, පුවරු කළමනාකරු තෝරන්න, ESP සොයන්න, සහ ස්ථාපනය ක්ලික් කරන්න.
4. පැති තීරුවේ, පුවරු කළමනාකරු තෝරන්න, M5Stack සොයන්න, සහ ස්ථාපනය ක්ලික් කරන්න.
Depending on the product used, select the corresponding development board under
Tools -> Board -> M5Stack -> {ESP32C6 DEV Module board}.
5. වැඩසටහන උඩුගත කිරීම සඳහා දත්ත කේබලයක් සමඟ උපාංගය ඔබේ පරිගණකයට සම්බන්ධ කරන්න.
ලේඛන / සම්පත්
![]() |
M5STACK ඒකකය C6L බුද්ධිමත් දාර පරිගණක ඒකකය [pdf] හිමිකරුගේ අත්පොත M5UNITC6L, 2AN3WM5UNITC6L, ඒකකය C6L බුද්ධිමත් දාර පරිගණක ඒකකය, ඒකකය C6L, බුද්ධිමත් දාර පරිගණක ඒකකය, දාර පරිගණක ඒකකය, පරිගණක ඒකකය, ඒකකය |